Program timer button keeps flashing. how do I get it to go to just tv

1) If timer worked before and stopped working, then manual says last step is to reset timer.
If timer will not function after reset, then timer is broken.

2) You posted under battery-operated ST01C timer, that comes with 1 year limited warranty.
Open following page to identify timer, read ez instructions, and download on-line manual
http://waterheatertimer.org/ST01C-program.html

3) How to reset ST01C
Hold down on-off button and press reset button
Release reset button.
Keep holding down on-off button until INIT flashes on screen.
Release on-off and 12:00 will flash
Re-program timer using ez steps shown on link above.

Add a comment for more free help.
Also take advantage of fixya expert assistance live.
For a price, expert works with you while you work on timer or any do-it-yourself project.
Fixya is always less expensive than a service call.

Hello
Timer function is in ON position and have been set to the least time I thinks. You just go to the menu and put the timer fuction of OFF.

The On/Off timer lets you program your television to turn itself on or off. You can use it as an alarm

to wake up, to help you remember important programs, or as a decoy when you're not home.

Press the MENU button

Press UP or DOWN button on the remote control hanset to ON/OFF TIMER

Make it OFF.

Switch off the TV by its front panel power button, and switch it ON again after 10 seconds.

OK.

N1505 timer manual:
http://waterheatertimer.org/pdf/Woods-49122-N1506-manual.pdf

N1506 is heavy duty outdoor timer with display screen.
Plug timer in and display flashes C.
Set current time: press Time button once and display shows 1 am
Keep pressing time button until current time with am pm displays.
Dot in lower right corner corresponds to pm hours.

To set timer program:
Press Mode button, display flashes P
Press Time button until desired ON time displays.
Press Mode button again and display flashes E
Press Time button until desired OFF time displays
When programming is finished, press Mode button and display shows current time.

To reset timer, unplug timer for 10 seconds and re-program timer.
Timer must be reset after power outage. Display will warn by flashing C.

Plug lights into timer.
If lights have a switch, switch must be on.

For manual override, press Mode button, and display shows O and lights will be ON until next program change.
To use timer function, press Mode button until current hour displays.

N1505 timer manual:
http://waterheatertimer.org/pdf/Woods-49122-N1506-manual.pdf

N1506 is heavy duty outdoor timer with display screen.
Plug timer in and display flashes C.
Set current time: press Time button once and display shows 1 am
Keep pressing time button until current time with am pm displays.
Dot in lower right corner corresponds to pm hours.

To set timer program:
Press Mode button, display flashes P
Press Time button until desired ON time displays.
Press Mode button again and display flashes E
Press Time button until desired OFF time displays
When programming is finished, press Mode button and display shows current time.

To reset timer, unplug timer for 10 seconds and re-program timer.
Timer must be reset after power outage. Display will warn by flashing C.

Plug lights into timer.
If lights have a switch, switch must be on.
For manual override, press Mode button, and display shows O and lights will be ON until next program change.
To use timer function, press Mode button until current hour displays.

The ST01C programming is long and hard to understand
Intermatic has posted a EZ-version for programming
http://www.intermatic.com/products/timers/consumer%20indoor%20timers/in-wall%20timers/st01c.aspx

http://waterheatertimer.org/ST01C-program.html

First of all, you have to set current date on all brands of programmable timers before programming. On some timers, the wiring has to be correct before the timer will let you program.
If you have the ST01C, push the reset button with a paper clip until time flashes to 12:00, and then start over

When I have a problem with a timer, I go back to the manual and start writing out the instructions.
If you can write the instructions, then they usually make better sense >>> and then you wonder who wrote the manual.

Finally, the ST01C, and most digital timers, come with a 1-year limited warranty >> timers go bad.

http://waterheatertimer.org/pdf/Woods-49556-TD1300.pdf
Link above is the Woods 49555 manual

If the timer will not program, then it has gone bad.

Plug timer into wall receptacle
Back-up battery will charge in about 1-2 hours > if battery will not charge, then timer is no good
Some digital timers require back-up battery to be fully charged before display will show
Back up battery allows programming while timer is removed from receptacle
After timer is programmed, plug timer back into receptacle

Timer buttons show below



To set current time:
Depress RST (Reset) button to clear programs
Press-and-hold TIME button to select 12 hour or 24 hour display

Press-and-hold SET button. Mo Monday will flash in display
Push arrow button until current day shows

Press SET button again. Hours will flash
Press arrow buttons until current hour shows (am or pm)

Push SET button again. Minutes will flash.
Press arrow buttons until current minutes show

Programming ON-OFF
Make a schedule so programs don't conflict
You can set up to 20 on-off programs over 7 days
Each program has ON time Day Hours and Minutes
Each program has OFF time Days Hours and Minutes

Press right-arrow > PROG 1 ON flashes

Press SET > choice of day groupings flash
Press arrow button to select days

Press SET > program1 ON times flash
Press arrows to set ON time

Press SET > program1 for Hour

Repeat sequence described above to set MIN
Repeat sequence to set OFF times for program1
Repeat sequence to set Program2 thru Program20

Press TIME button to finish programming

have you try to turn off the timer in the tv menu
or you van try to disconnect from power line
then reconnected after a wile that should reset the set.....
hope that help you

The V26 DM repair kit should take care of that issue. The kit has the caps and the instructions. You can get it at www.tvrepairworld.com

http://www.jyerdon.com/tv/

If it`s a 65513 mitsu, this will fix the flashing green light, most of the time, e-mail me with any questions, good luck


[email protected]

does the tv have a separate tuner box? if so check the cables i have a pioneer that does that when the connection isnt in sync