Intermitant audio static

Clear picture but white noise and static?!!!!!. What do you say?. Check whether the audio is muted by accidental press at remote control button. Enter its sound menu, and check it. If muted, as you know there will be no audio output. If not muted, check the speaker/s. If found OK; check and replace the damaged component/s at its audio output section circuit board. If needy, replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. Surf the site with patience.
http://electronicshelponline.blogspot.com/

Check whether the audio is muted by accidental press at remote control button. Enter its sound menu, and check it. If muted, as you know there will be no audio output. If not muted, check the speaker/s. If found OK; check and replace the damaged component/s at its audio output section circuit board. If needy, replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. Surf the site with patience.
http://electronicshelponline.blogspot.com/

Check whether the audio is muted by accidental press at remote control button. Enter its sound menu, and check it. If muted, as you know there will be no audio output. If not muted, check the speaker/s. If found OK; check and replace the damaged component/s at its audio output section circuit board. If needy, replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. Surf the site with patience.
http://electronicshelponline.blogspot.com/

It's quite simple... Just change your 'power plan scheme'. Try using "High Performance" (located: win7, RHS corner,in notification area; winXP, Control Panel, Battery saving). Good Luck!
'A precise description is vital for a valid answer.'

you might have to tick the mute box the try your microphone first before unticking the mute box
control panel sounds and audio devices select advanced there might be a tick in the mute box untick it or select audio from the microphone drop down list make sure you have the right one selected and in the volume box make sure the microphone box has a tick in it or select the voice tab and make sure that you have the right media selected also select volume make sure the box for microphone has a tick in it
hope this helps

I was having the same problem - I ended up just playing with it until it worked again. I found instructions on muting the H700, which is to tap both volume buttons at once. I did that a few times while on a call (I was actually listening to my voicemail), and then I hit the volume up button, and now it works. Not sure if something is loose inside and all I had to to was play around to get it back into place?

yes also u can check the mute from the right down icn of sound its a small speaker beside clock

Hi,

There is small logic to resolve or to narrow down the Audio issue.

Let me explain.

First, try to play any audio file and observe if is giving any error message or it seems to playing without sound.

If it gives any error message like "No Audio/Media device installed or found", then the audio driver is not installed in the computer or the Windows Audio serviceis stopped.

If it seems to be playing without sound, then somewhere it might be muted or Sound level might be lowered.

If you are sure that all settings are okay and not Muted, then you have to check with another speakers or headphones.

If another speakers works, then the issue is with the ols speakers.

Please get back to me if you need more information on this issue.

are you sure your microphone isn't muted?. Check your microphone volume setting by doing this:

Control panel > sounds and audio devices > click the audio tab across the top.

Under 'sound recording' , click volume. turn your volume up on the selected device. you may even need to change the selected device to the correct one. Play arround with that audio screen until you get it to work

Regards

Tony

Error 6 & 4 it means laser is not reading the disc and unforutunally you need to replace the pick up laser assy.
You can get it from pacparts.com,but I reccomend you to take to a proffessional tech because this is a "static sensitive" item.