Sharp 5320 H2 error code

Put on ur machine & go 2 ur display board & press the C button twice then ur display will go off then input figure 1 & 4 that is 14 then press the print button. if this fails then remove ur fuser unit & check d thermistor, clean any dirt b/w d fuser roller & the thermistor, u can test d thermistor by connecting the two terminal 2 ohms meter

Press Keys : # interupt C interupt....................... then machine will be powered off then press Keys: 1 4 Copy then H2 will be removed. By [email protected]

The Fault fuzer. Possible faults of the block of the fastening the scene or in contact of the join or in signal of the controller of the direct current.
Address please in service Sharp
H2 00 Fusing unit temperature error 01 Fusing unit temperature error H3 00 Overheated fusing unit 01 Overheated fusing unit H4 00 The fusing unit doesn't heat up 01 The fusing unit doesn't heat up H5 01 Papersensordefective in the fusing unit 02 Fusing unit temperature error

Sharp Fuser
H2-0 Fusing unit temperature error
H4-0 The fusing unit doesn't heat up.
***ALWAYS DISCONNECT POWER WHEN WORKING ON MACHINE***
You have to reset fuser errors with simulation 14. Push P * C * then 14 then Start (the button you use to make copies) and it should reset the code. If not then replace the fuser.
SM 5-1 should turn the lamp on. If lamp blinks on and off it is the thermistor, if it does not it is the lamp, but check the contacts on the lamp/fuser -- they have been known to erode.
Also check thermal fuse, if defective replace.

In AR 275 Sharp copier H2 00 is very common problem, U have to only reset the above fuser error code as fallows

press # then intrrupt then c them intrrupt then display will show simulation mode then enter 14 then press ok key


If this is not enough then press press thermostat on fuser unit by removing the unit from machine this requires tech knowledge

OR you can try by replacing thermistor of fusing unit

If by above procedure the prob is not solved then and then you replace the fusing lamp

Even though u can check the lamp by removing back cover and turn on the machine u can observe the light of fusing lamp

pl ask for any difficulty.

Hi,

H2 indicates there is a fuser error.

Try resetting it by the pressing the following buttons on the display in sequence,

#, interrupt, Clear, interrupt,

display should go dead,

enter 14,

then press print, This will clear the error code

press CA to get out and return to normal.

However if there is still a problem with the fuser, the code will return. Then you may need to have a tech look at what is the problem.

Hope that helps...

Lbcoaster

H2 is a fuser Error. There should be another 2 digit number that is flashing that is the 2nd part of the error code.
Without the 2nd code I cannot look up the code to narrow it down.
Let me know what the other flashing 2 digit code is and I can give you a more specific answer.

Most likely, you will need a service call to get your machine working again since the fuser unit on these machines are really not made for consumers to remove and repair.

But, there is a slight chance that you might be able to get it working again, so let me know what the 2 digits are after the H2.

Hope this helps.
Good luck.
Mac =)
(please remember to rate this answer if I have helped you. THANKS =)

You have a thermistor open. That means that the device that reads the temperature in the fusing unit, has broken. You will need to replace the fusing unit to fix this problem. You could try a Sim 14 reset. Push P * C * then 14 then Start (the button you use to make copies) and it should reset the code. If not then replace the fuser.

An H2 is an indicator that the temperature sensing device is reading open, preventing the machine to warm up. There is only one way to correct this and that is to replace the thermistor, and that takes a technician. Not a hard job but a novice could get into trouble and make matters worse. Aloha, Bill Monroe