What is code oL - Whirlpool Cabrio WTW6600SBK

OL = Overloaded.

Is the Washer overloaded? If OL (overloaded) appears in display, the load too large. If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent.Feb 24, 2020

OL - Error Code - Top Load Washer - Product Help - Maytag

Maytag https://producthelp.maytag.com > ... > OL

The washer has ol on it at the end - Maytag Bravos quiet ...

iFixit https://www.ifixit.com > Answers > View > The+washe...
Oct 6, 2014 · 2 answers
First, OL stands for "Overload", so in other words, the washer thinks the tub is too hard to move because it's overloaded and the motor is ...
OL code all the time even with very small and light ...
2 answers
Sep 28, 2016
Why washer stops and gives code "ol" - iFixit
2 answers
Nov 30, 2016
at the end it says OL - Maytag Bravos quiet series 300 ...
1 answer
Dec 29, 2022
OL code showing . - Kenmore 110 Series Washing ...
2 answers
Sep 19, 2017
More results from www.ifixit.com

What does the error code say

OL means the washer is overloaded or there is excessive drive load. Go to the link for a full explanation of the OL code and its repair. What might be causing the OL error code on my Whirlpool Cabrio washer...

"oL" error code, even when unloaded - Fixitnow.com

fixitnow.com/.../whirlpoolkenmore-cabrio-and-maytag-bravo-washers-th...
Sep 18, 2010 - The "oL" error code in the Cabrio and Bravo washers means the ... is almost always caused by using non-HE detergent in this washer- see this ...

Have the cylinder one misfire repaired and other codes will likely disappear.

Hi jbrundage1. I believe you have a UL error code on the washer. It means that the sensors in the washer are sensing the unit is unbalanced. When the washer is empty, set it to a spin or rinse and spin setting. Run the washer through the cycle empty, as it will help to remove any excess water in the tub. Also, make sure the washer is level, as it is balanced on springs, and that could be throwing the sensors off. I hope these suggestions prove helpful. Sincerely, Melanie, Maytag Social Media Representative.

From the FAV6800A/FAV9800A Service Manual page 14 that error code = oL Machine Paused-Load Wedging

Google this "16022808 Revision 0 December 2003" to find the Service Manual if you are going to DIY the fix.

OL error means the Motor Controller has sensed an Overload.

The oL code means the motor control board is struggling to power the motor up. If it recurs after removing some clothes - usually this means a new motor control.... or worse - a new bearing.

If it were a problem with the tub floating up, the unit would spin instead of nutate.

Bearing failure in this machine is very common.

I suspect the drive shaft and bearing are the problem. The bearing and shaft are part of the outer tub.

The new outer tub with bearing W10128830 cost approximately $197 dollars.

If you can get access to the shaft it may be an Emory cloth will help smooth things down so that you no longer get the OL code.

This is an ambitious do-it-yourself project... as most appliance repairmen don't understand how this machine operates.




http://media.fotki.com/1_p,srrtbrrfbdbqgkkxgtqsskgwtqkq,vi/bqkfstqqfxrqqbkwgqdxbwsqrwrtq/1/1303472/5961857/image828956817962821589img-or.jpg




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

OL, usually means Over Loaded. It is an error code thrown up by the on board computer.. generally when TOO much wet weight is in the bowl.

OL error means the Motor Controller has sensed an Overload.

The oL code means the motor control board is struggling to power the motor up. If it recurs after removing some clothes - usually this means a new motor control.... or worse - a new bearing.

If it were a problem with the tub floating up, the unit would spin instead of nutate.

Bearing failure in this machine is very common.

I suspect the drive shaft and bearing are the problem. The bearing and shaft are part of the outer tub.

The new outer tub with bearing W10128830 cost approximately $197 dollars.

If you can get access to the shaft it may be an Emory cloth will help smooth things down so that you no longer get the OL code.

This is an ambitious do-it-yourself project... as most appliance repairmen don't understand how this machine operates.




http://media.fotki.com/1_p,srrtbrrfbdbqgkkxgtqsskgwtqkq,vi/bqkfstqqfxrqqbkwgqdxbwsqrwrtq/1/1303472/5961857/image828956817962821589img-or.jpg




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question