GE WBSE2090A Top Load Washer Logo

Related Topics:

A
Anonymous Posted on May 12, 2014
Be the first to answer

Ge 2009 washing machine not spinning clothes

How to put timer back in time

Answer This Question

5 Related Answers

Anonymous

  • 1294 Answers
  • Posted on Sep 12, 2007

SOURCE: GE Washing machine won't spin in rinse cycle

Possible your outlet filter is blocked. This requires cleaning depending on your usage. Clean this out and refit. Good luck. Plug off the wall first.

Ad

Anonymous

  • 1 Answer
  • Posted on Apr 15, 2008

SOURCE: GE front load washer (clothes)

THANK YOU. for those of you with a screw driver, here are the photos on how to.

It takes a philips screw driver and 20 minutes. The white screws may not align perfectly but don't worry, just get them to go back in the hole(no harm done).

I'm going to admit it was my wife that found this fix, so now I give the step by step photos.

[IMG]http://i26.tinypic.com/23upff6.jpg[/IMG]
Small white screws (3 in total)
[IMG]http://i30.tinypic.com/69n9eh.jpg[/IMG]
cover "falls" off
[IMG]http://i29.tinypic.com/24erogl.jpg[/IMG]
Unscrew the lint trap (turn to the left)return when clean to hand tight
[IMG]http://i32.tinypic.com/9uralw.jpg[/IMG]
Bob's your uncle and a freebee for CMKX'rs.

Hub and wife team.

mpservices

  • 191 Answers
  • Posted on Nov 22, 2008

SOURCE: GE WASHER SPIN OUT PROBLEMS

Sounds like the suspension for the drum is having problems - there are usually springs holding the drum up and acting as shocks - one of the springs may have come off during an unbalanced load.

Anonymous

  • 2 Answers
  • Posted on Apr 15, 2009

SOURCE: GE profile washing machine won't agitate it spins out, drains,

Pull the agitator out and check the drive collar splines.If you have the model I think you have just pull straight up on the agitator. Once removed you will see the drive collar with a 7/16 head bolt,remove it and pull off the collar.First before pulling it off spin it if splines are stripped it will spin freely.

Anonymous

  • 3600 Answers
  • Posted on Sep 10, 2009

SOURCE: Brand new GE Profile leaves clothes soaking wet

It is under warrenty call the store where you bought it and have them look at it. If you mess with it it will void your warrenty, belt may not be working or transmisson may not be shifting. The house call will be at no charge.

Testimonial: "thankyou for the help, I thought I had just made a bad buy. They sent someone out right away and it turns out this particular machine had a bad part."

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

Spin. Working short time do not put cloth water out
Sounds like the belt that spins the washing drum is slipping. It my need to be adjusted or replaced, or try washing a smaller load of laundry.
Read full answer
Mar 10, 2016 • GE Washing Machines
0helpful
1answer

Ge washing machine fills up with water on spin cycle
Sounds like the timer is screwed... Sending out the wrong signals and the dryer is doing the rinse cycle when it should just be the spin cycle. Do t know what your timer looks like in that washer but most now days look like the picture. 11_11_2013_2_52_52_am.png
Read full answer
Aug 16, 2013 • Washing Machines
0helpful
1answer

My frigidaire front loader washer won't go into spin cycle after the clothes are washed
Sounds like you need a technician to diagnose the timer of the unit. Also the sensor that communicates to the timer.
Read full answer
Aug 12, 2012 • Frigidaire ATF6000ES Front Load Washer
0helpful
1answer

GE clothes washer WHDSE820C1WW started filling itself up and i cant get it to discharge the water out, spin or anything
Hi,

Problems with a washing machine not spinning or not draining are often interrelated..

If you are having a problem with your top load washer then check out thistip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkoutthis tip...

Front Load Washing machine not draining and or not spinning


heatman101 .
Read full answer
Oct 10, 2010 • General Electric Clothes Washer Timer Hub...
2helpful
1answer

Waher will not go into spin cycle. It makes a buzzing noise and will not spin.
it's most likely your timer....u can get the machine to spin out your clothes by pushing the timer in and pulling it back out. this resets the motor and makes it turn backwards. it's a pain to do this because you have to keep an eye on the time. this will get you through until you change the timer.
Read full answer
May 28, 2009 • Whirlpool Ultimate Care II LSQ9549L Top...
2helpful
1answer

CLOTHES STILL WET AFTER SPIN CYCLE
Dear dgloss1856, Sun 4-12-2009 1:14PM EST USA

Washers will shut down automatically without completing the spin cycle for two reasons.
1) Too many clothes in the washer at once (overloading with clothes) !
2) Too much soap in the washer when washing!

When this happens you should restart the machine in the spin cycle or if you can't start in spin run a full cycle without adding soap.

If this doesn't solve the problem you may need to clean the timer or control circuits depending on your machine by cleaning with electronic spray cleaner (available at Radio Shack) by spraying the timer or control circuits as instructed on the can of electronic cleaner.

cd1ee64.jpgLet me know if I can be of further assistance!
Read full answer
Apr 12, 2009 • Washing Machines
0helpful
1answer

GE Top Load Washer WLSR2000G3WW~smells like burning and wont drain
The clothes are wet after spinning When the clothes are wet at the end of a cycle, check these:

Motor coupler
Spin cycle
Siphoning
Water-inlet valve
Motor coupler To test the motor coupler, re-start the washer in its spin cycle. Let the machine run for a minute, and then open the lid and notice whether the tub is spinning:

  • If it's spinning when you lift the lid, the coupler is fine.


  • If it isn't spinning--and your machine was produced by Whirlpool®--you may have a broken coupler. Many Whirlpool-made washers use a small, relatively inexpensive device called a motor coupling. This plastic-and-rubber component is mounted to the shaft of the motor on one side, and to the transmission on the other. Over time, the coupler wears out and fails. When that happens, you need to replace it completely.


Spin cycle If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag®), a worn clutch (GE®/Hotpoint®), or a worn motor pulley or tub bearing. Replace the applicable component.

Alternatively, there could be clothes caught between the inner and outer tubs. Read the "It spins but won't pump" section of the "It won't drain" section. Also, there could be other things that cause friction on the drive train. Seek the assistance of a qualified appliance repair technician.

Siphoning If the water that pumps from the machine goes right back into the machine after the spin cycle, it may be because your washer is siphoning the water from a laundry tub with a slow drain, back into the washer. Try to improve the draining of the laundry tub. (Is there something stuck in the drain?) Also, be sure the drain hose doesn't reach more than about 4 inches into the laundry tub. If it does, cut off the excess.

Water-inlet valve Water-inlet valves eventually fail. One problem that may develop with a water-inlet valve is that it can no longer completely shut off when the electricity is turned off to it. Then, the valve may leak and drip water into the clothes tub--you may notice that your washer has water in it when you haven't used it for a few days. To fix this, replace the valve.

The cycle doesn't advance When the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

  • It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.


  • It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.
Read full answer
Nov 06, 2008 • GE WBSR3140DW Top Load Washer
0helpful
3answers

Does wash clothes
depending on what washer u have this could be a sign that your carbon brushes are on there last legs not much to replace them but need to know what make off washer it is hun peter
Read full answer
May 27, 2008 • Washing Machines
1helpful
2answers

GE Adora front load washer overloaded now won't start
Washers - Resetting Electronic Controls on a Washer

If there is a pause in the washer cycle, the controls will lock up. The pause can occur because of a power failure or it was put in the test mode at the factory.

Also, if the washer was stopped before the cycle was complete or the consumer has pushed the stop/pause button to temporarily stop the cycle and the cycle is not reset. Over a period of 24 hours, the washer will pump out and spin, but will stay in the final spin.

To correct the situation, shut off the circuit breaker for 30 seconds or unplug the washer, then turn the timer knob around and back to any position other than final spin. Verify the water is turned on and restore power. This should resolve the issue.

Read full answer
Apr 23, 2008 • GE WSXH208A Front Load Washer
2helpful
2answers

Old GE Washer WNSR2100T8WW will not pump out water nor spin
Possible your outlet filter is blocked. This requires cleaning depending on your usage. Clean this out and refit. Good luck. Plug off the wall first.
Read full answer
Sep 12, 2007 • GE WJSR2070B Top Load Washer
Not finding what you are looking for?

View Most Popular

WBSE2090A Top Load Washer

  • Washing Machines

Related Question

Spin. Working short time do not put cloth water out

  • GE Washing Machines

68 views

Ask a Question

Usually answered in minutes!

Popular Questions

GE front load washer (clothes)

GE WSXH208A Front Load Washer

My Ge washing machine is leaking from the Bottom

GE Profile Performance WPSF4170WAA

GE top load Washer ripping clothes

GE Energy Star WCVH6260F Front Load...

"Dr" error code

GE Spacemaker WSLP1100D Top Load...

GE Adora Front Load Washing Machine Problem

GE WSXH208A Front Load Washer

Top GE Washing Machines Experts

Brad Brown

Level 3 Expert

19187 Answers

Virgil Watts

Level 2 Expert

267 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1212 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...