I changed the bulb and it shut off in ten minutes the vender suggest I use the reset button on front panel. is this safe?

Hello Jeff;
If the TV does not turn on or off, does not respond to the remote
control or the control panel buttons, or has audio but no video:
1.) Press and hold the POWER button on the control panel for ten seconds. The TV will turn off.
2.) Power on the TV and the green LED will flash quickly for about one minute. The changes you made most recently, before using SYSTEM RESET, may be lost.

If the TV does not respond to the remote control or to the control-panel buttons and TV will not power on or off.
• Unplug the AC power cord for 10 seconds.
• Press and hold the POWER button on the control panel for 10
seconds to perform a system reset.

If the TV turned itself off and the light on the front panel started to flash:
• Momentary power fluctuation can cause the TV to turn off to prevent damage. Wait for the green light to stop flashing and turn the TV on again.
• If the TV does not stay on, press the POWER button on the
control panel for ten seconds to perform a System Reset. If this happens frequently, obtain an AC line power conditioner/surge protector.
• An unusual digital signal may have been received, triggering a
protection circuit. Wait for the light to stop flashing and turn TV
on.

If the TV will not power off, press the POWER button on the control panel for ten seconds to perform a System Reset.

Should you still have problems, call for assistance at 1(800) 332-2119

I would not recommend using compressed air or any other method that would blow dust around- since the dust could make its way into the set's circuitry via the grille or vents and cause problems. Use a vacuum cleaner with a brush attachment instead.

Thank you for your inquiry, John Sodt!
From what you have described your Frigidaire refrigerator's filter display is not changing back to green after the filter has been changed. This could be a miscommunication within the control panel and to clear out any miscommunications I would suggest performing a reset on your refrigerator. The best way to reset your refrigerator is to unplug the power cord for roughly ten minutes. If that does not help your issue you may want to speak with a professional technician. Good luck. -Matt

Hi friend, thanks for your post!

I see that your filter light is not turning green on the panel of your Frigidaire refrigerator. If you have recently changed your filter I would suggest pressing and holding the filter reset button. Should that not correct the issue I would perform a reset on your refrigerator and you can do that by unplugging your power cord or flipping the household circuit breaker off for roughly ten minutes. I hope this has been beneficial. -Matt

Good Morning friend, thank you for your post!

From my understanding your Frigidaire dryer, LEQ1442ES1, will run and then shut down after three or four minutes. I would recommend a reset on your dryer which you can do by unplugging your power cord for roughly ten minutes.

If that does not correct the issue it sounds like a potential problem with your control panel or a sensor. I would suggest having a professional come out and repair your appliance to avoid any unnecessary part purchases. -Matt

It might just need a reset. Press the Pause and off button, then pull the plug from the wall.
Wait ten minutes and power it up again. Check the door very carefully, make sure it is shutting correctly.
Try a restart.

Open the front panel. Just to the left of the RCA imputs is a small button that says reset. You may need to use a pen or paper clip to press it. Press that and the system will reset .That should fix your issue, or do like me and get a Sharp. LOL. My bulb went out 2 times and I got irritated with it.

it sounds like the bulb is causing it to overheat make sure the fans are running and that no of the air vents are clogged or blocked. Also did you buy a cheap alternative or authorised bulb for it?

did you clean screen in lamp housing this is a must if just replacing the lamp only!

Solution: Press ON/OFF switch and wait a few minutes before powering back on the device

Reset the device when it is not functioning properly. If the device is not functioning properly or to clear an error, power off the printer and power it back on. Before powering back on the printer, wait five to ten minutes.

1. On the operator panel, press the <ON/OFF> button. (The display will go blank.)
   
   Note: On rare occasions, it may be necessary to unplug the power cord if pressing the ON/OFF button does not shut off the printer.
   
   
2. Wait approximately five to ten minutes and then press the <ON/OFF> button again.
   
   
3. Wait until the device has completed its cycling process before submitting another job request.

FYI - There is a firmware update for this unit as well

Did you get the exact replacement lamp? Some have 1.1 arc gap some have 1.3 they wont interchange. If you got the exact lamp and your trouble is still the same. It could possibly be your ballst.