How can I fix our printer displaying a Call Service 4600 error message?
An expert who has achieved level 2 by getting 100 points
LSU cleaning motor error
When the LSU cleaning motor
is driven, an error signal is
detected continuously for 1 s.
Defective connector
cable or poor
contact in the connector.
Reinsert the connector. Also check for continuity
of the connector cable. If none, replace
the cable.
Posted on Aug 06, 2014
Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Good luck!
Posted on Jan 02, 2017
SOURCE: Kyocera Printer error - Help!
The code is for a defective cyan motor. So its either the cyan toner motor or a lump of toner inside the cyan toner container.
Posted on Aug 24, 2008
SOURCE: I have a FS-1118 MFP
yyou have to be careful when doing this.
the waste toner is built in to the process unit (drum unit) and has a plug on the side.
remove the plug and tip it out.
Posted on Mar 10, 2009
SOURCE: I have a kyocera FS-2000D with error code: Call fo...
Error code 0150 is an engine EEPROM communication error. The engine board might need to be replaced. I have heard that sometimes a defective developer unit could cause this same error code. I would try swaping a develper from a working FS-2000D first.
Posted on Jun 09, 2010
SOURCE: I HAVE A KYOCERA ECOSYS
The error indicates - Engine PWB EEPROM error Detecting engine PWB EEPROM communication error. Causes - Improper installation engine PWB EEPROM. Check the engine PWB EEPROM installation,
- Defective engine PWB. Replace the engine PWB
IF turning the printer off and unplugging then plugging back in and turning back on doesn't correct the problem I would suggest you contact an authorized Kyocera service center such as www.gfbm.net.
Posted on Jan 27, 2011
SOURCE: kyocera FS-1016MFP "printer error service
Code: 6000
Contents: Broken heater lamp error
The temperature won't rise by 1°C/33.8
°F during warming up and the heater is
turned on for 5 seconds.
The temperature won't rise by 1°C/33.8
°F during printing and the heater is
turned on for 5 seconds with the duty
cycle more than 60%.
Causes:
- Defective fuser thermistor.
- Broken thermal cutout or heater lamp.
- Defective engine/high voltage PWB.
Posted on Feb 21, 2011
Apr 07, 2017 | Kyocera Office Equipment & Supplies
Oct 04, 2016 | HP Color LaserJet 4650DTN Printer
Mar 31, 2016 | Kyocera FS-C5250DN Duplex Network Colour...
Jul 27, 2015 | IBM Infoprint 1532 Laser Printer
May 04, 2014 | Kyocera FS-1118 Printer
Mar 26, 2014 | Kyocera Fs-3920dn Laser Printer
Oct 17, 2011 | Kyocera FS-1016 Printer
(Select) button to continue. (Select) button. (Select) button until the Ready, Data, and Attention lights flash once, and then stay on steady. (Select) button when the Ready, Data, and Attention light are on steady.
(Down Arrow) button once. The control panel will display COLD RESET . (Select). The printer will perform a cold reset and then continue its power-on sequence.Oct 01, 2011 | HP LaserJet 4600 Printer
May 31, 2011 | Kyocera FS-2000D Laser Printer
Feb 14, 2011 | Kyocera FS-4000DN Laser Printer
Apr 28, 2014 | Kyocera FS-C5030N Led Printer
3,669 people viewed this question
Usually answered in minutes!
×