Televison & Video Logo

Related Topics:

A
Anonymous Posted on Jun 05, 2014

Tx-p42ut50b red light flashes 3 times?

2 Related Answers

Craig McVeigh

  • 19 Answers
  • Posted on Jun 06, 2009

SOURCE: stand by light flashes red on powering up with remote and the green light flashes approx 15 or times before the screen illuminates.

thats pretty normal, it takes a good second or two to warm up and the display to turn on(at least0, you get the green flashes as you hold for on, 1 sec is a long time at times, lol, be patient, no problem with your tv!

Ad
roety

Eric Rotmil

  • 587 Answers
  • Posted on May 04, 2012

SOURCE: Panasonic TX-P42X10B wont turn on - goes into standby

Hard to troubleshoot with just this info, the red light can be helpful if its 10 blinks repeating over and over replace the power supply first then the A board. Voltages check on the power supply would narrow down the culprit.
Post again if you measure the power supply voltages

I’m happy to help further over the phone at https://www.6ya.com/expert/eric_ab7c09ec01841771

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Onkyo tx ds777 remote does not working

How to check remote infra red:
(0)switch on a mobile digital camera with lens pointing to the infra red diode mounted on the remote.
(1)press a remote button
(2)if infra red doide is ok,you'll see white light flashing. Press other buttons to prove good or bad.
(3)if no flashing white, infra red isn't sending out.
(4)use any good remote to see what happens.
2helpful
2answers

Panasonic TX-L42E5B blinks 3 times which board is faulty

When an abnormality has occurred to the unit, the protection circuits operate and set the unit to stand by mode. At this
time the defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.

Fault maybe on the A board 3.3V SOS give me your email & i send you the full timing chart.
0helpful
1answer

Panasonic tv will not turn on red light flashing 3 times what does it mean

I hooked a exterior camera up to comp.1 and it worked just fine for hours then the whole thing shut down and light wouldn't stop blinking 3 times so I disconect the camera unplug tv for 3 mins plug everything back up and this time put camera on video 2 and it all works fine. It was like duh did you check to see if it had gas.
0helpful
1answer

Panasonic TX-P42X10B wont turn on - goes into standby

Hard to troubleshoot with just this info, the red light can be helpful if its 10 blinks repeating over and over replace the power supply first then the A board. Voltages check on the power supply would narrow down the culprit.
Post again if you measure the power supply voltages

I’m happy to help further over the phone at https://www.6ya.com/expert/eric_ab7c09ec01841771

0helpful
1answer

Stand by light flashes red on powering up with remote and the green light flashes approx 15 or times before the screen illuminates.

thats pretty normal, it takes a good second or two to warm up and the display to turn on(at least0, you get the green flashes as you hold for on, 1 sec is a long time at times, lol, be patient, no problem with your tv!
0helpful
1answer

Rx/tx light flashes red and green at same time

sounds like a bad pll.that will have to go to a shop that knows what they're doing.good luck
0helpful
1answer

Set up new tv - doesn't work

Warranty time. The TV most likely went into protection mode because a part went bad inside.
I would take it back to the store and exchange it for a new one. 90 day warranty policy.
Have them test the new one to make sure it works so you don't have to waste another trip.
Good Luck
0helpful
1answer

TV WONT TURN ON, STAND BY LIGHT FLASHING 3 TIMES CONTINUOUSLY

having problem with sony television the screen when its turn on no images found just found red color on the screen..
0helpful
2answers

Hdtv won't turn on

Can you count how many times it flashes ? It might flash like 6 times and pause for 2 sec and flash 6 times again. THen call a service comany and tell them this info and they might tell you what part inside is bad. They are not telling you this for you to replace but they might say something like oh 6 flashes is a Y board and we will have to order it.
Hope this helps
Not finding what you are looking for?

220 views

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts

 Grubhead
Grubhead

Level 3 Expert

5755 Answers

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...