ABC are green lighta and D is orange - Dell OptiPlex GX280 PC Desktop

Red = ground
black = ground
Grey/blue = Left rear (+)
yellow/black = ignition 12v
white/purple = right rear (-)
green/black = (could this be green / violet?) than it is 12v constant
blue/red = illumination
orange/green = left front (+)
white/green = right front (-)
blue/white = left front (-)
brown/yellow = left rear (tan / yellow) (-)
green/orange = right front (+)
orange/red = right rear (+)
blue = not used

Straight Cabling :

Side 1 Side 2
White Orange White Orange
Orange Orange
White green White Green
Blue Blue
White Blue White Blue
Green Green
White Brown White Brown
Brown Brown


Cross Cabling :


Side 1 Side 2
White Orange White Green
Orange Green
White Green White Orange
Blue Blue
White Blue White Blue
Green Orange
White Brown White Brown
Brown Brown

Hope this helps. Please rate my response.
Thanks.
Have a good day.

white/blue
white orange
white green
white brown
white slate
red blue
red orange
red green
red brown
red slate
black blue
black orange
black green
black brown
black slate
yellow blue
yellow orange
yellow green
yellow brown
yellow slate
violet blue
violet orange
violet green
violet brown
violet slate
**Keep all pairs together and you should be fine***

Hello there
Canon Pixma iP4200, Reset Procedure

1. Turn off the Printers.
2. Hold Resume button click POWER.
3. Hold button RESUME, release POWER
4. Then press the button again twice RESUME.
5. Release all the buttons.
6. Indicator led in green and stay green.
7. Click the button 4 times RESUME, if you want to make another transaction. :

Look at the table below:
· 1 led- Orange – Service test print 1 times – Orange – Service test print
· 2 led – Green – EEPROM information print 2 times – Green – EEPROM information print
· 3 led – Orange – EEPROM initialization 3 times – Orange – EEPROM initialization
· 4 led – Green – Waste ink counter setting 4 time – Green – Waste ink counter setting
· 5 led – Orange – Destination setting (Press Power > Press Resume 3x) 5 times – Orange – Destination setting (Press Power> Press Resume 3x)
· 6 led – Green – Print head deep cleaning 6 times – Green – Print head deep cleaning
· 11-13 led – Orange, Green, Orange – Return to menu selection
· 14 led – Green – Left margin correction 14 times – Green – Left margin correction

1. Turn off the printer POWER button.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Bob, Handheld radios will talk line-of-sight up to 2 miles (3.2 km). Any obstacles you put between the radios will shorten the range. Talking from inside to outside you might expect only 1/4 to 1/2 mi. (.8 km to 1.0 km). For best range, hold the radio upright with the antenna perpendicular to the ground.

The buttons can do a variety of functions. It would be subject to how the dealer programmed the radios, so there is no way to tell you what exactly your buttons will do. Some options include Hi/Low Power, Scan, Monitor and Sticky Monitor. The Orange button on top is sometimes programmed as an emergency button when used by public safety (Police/Fire/etc).

The 1-15 would be the channel knob. The radio is capable of several channels. This also would be subject to the dealer who programmed the radio. The ABC switch can also be programmed for various functions. It would be best if you were wanting to know how the radio is programmed to visit your local dealer and have the radio read-out.

This radio when fully charged, should work like any other walkie-talkie, where you press the PTT button when you want to talk, and you release the button when you want to listen.

Best regards.

When you are on the message screen, there is a little orange block on the upper right corner that (at least on mine) shows "Abc".

If you press the # button, it will cycle thru "ABC", then "123", then "abc".

If you leave it on "ABC". then you have all caps.

I have the Canon Pixma iP4000R printer. I had an error code of a600 and my power light was blinking/flashing green-orange-green-orange-green-orange-green-orange-green-orange-green-orange-green-orange-green-orange-green-orange-green-orange-green-orange-green-orange (12 oranges).

I tried the “waste ink counter reset reset” procedure: Power on while holding the stop/reset button and pushing the service button twice, then pushing the stop/rest button 4 times to clear the error, but that didn’t work.

My ink cartridge carrier wasn't moving. I thought I had a paper jam.

I looked at a few blogs about my error on other Canon Pixma models and they kept talking about “sponges”.

The following is what I discovered that cleared my error and now my printer is back to printing!

The “sponges” are 2 hard pieces of absorbing plastic or something of the like. I was looking for a softer material like long thin gray foam strip material in my printer. The 2 "sponges" on my Pixma iP4000R were next to each other-one was rectangular and one was square-like. Originally they were white but the ink made them black/navy.

The "sponges" are located on the right under where the ink cartridge carrier "rests".

I didn't see the sponges at first, as there was a white “L” shaped plastic piece that had a spring attached to it. The “L” shaped piece was moved forward out of its place. I used my pen tip and pushed that piece back and found that the rectangular "sponge" had popped out of its place.

I used a pen tip popped both “sponges” out and rinsed them with water and voila they were once again white. I think the rectangular one had so much ink on it it popped itself out of place.

My error is gone and I can print again!

Pin Std Phillips
1 White/Orange BLUE
2 Orange Orange
3 White/Green Black
4 BLUE Red
5 White/Blue Green
6 Green Yellow
7 White/Brown Brown
8 Brown White

.
How to Reset Waste Ink Protection Counter Canon Pixma IP8500 Printer

Instructions:
Resetting Waste Ink Counter Canon Pixma IP6000, Canon MP450, Canon Pixma IP8500

1. Turn off the printer.
2. Whilst pressing Resume button also press on POWER.
3. Then Press RESUME button and release POWER.
4. Then Press RESUME button again .
5. Then release all buttons.
6. Led Indicator should be green and stay green.
7. Click RESUME button 4 times if you wish to try again.

Then See Table Below:

Orange - Service test print ONCE - Orange - Service test print.
Green - EEPROM information TWICE - Green - EEPROM information print.
Orange - EEPROM initialization 3 TIMES - Orange - EEPROM initialization.
Green - Waste ink counter resetting 4 TIMES - Green - Waste ink counter resetting
Orange - Destination setting (Press Power then Press Resume 3x) 5 times - Orange - Destination setting (Press Power Press Resume 3x)
Green - Print head deep cleaning 6 TIMES - Green - Print head deep cleaning.
Orange - Green, Orange - Return to menu selection 11-13 TIMES - Orange, Green, Orange - Return to menu selection.
Green - Left margin correction 14 TIMES - Green - Left margin correction.

8. Turn off printer.
9. Restart Printer.
Good Luck!

Tinteiros - Magic Inkjet Flush (Ebay)