Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver Logo

Related Topics:

A
Anonymous Posted on Jun 24, 2014
Be the first to answer

How to remove bit stuck in chuck Ramset? - Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver

Answer This Question

4 Related Answers

A

Anonymous

  • Posted on Aug 09, 2008

SOURCE: stuck bit

I HAD THE SAME PROBLEM AND STILL DO FROM TIME TO TIME. I USE THE PROPPER BITS, SO THAT ISNT THE PROBLEM.
WHAT WORKS IN GETTING THEM OUT... JUST TAP THE BIT INTO THE CHUCK AND THEN PULL THE QUICK RELEASE AND THE BIT COMES RIGHT OUT. THE BIT JUST GETS INTO A BIND AND TAPPING THE END FREES IT UP

Ad

Anonymous

  • 17 Answers
  • Posted on Apr 06, 2011

SOURCE: I have a DEWALT DC920

try tapping on all sides of the chuck lightly with a hammer and wiggling the bit... you can also try to spray some oil into the chuck and see if that loosens the bit for you... You can also clamp the bit in a vise (or get someone with a pair of pliers) and pull, that will sometimes do the trick.

Anonymous

  • 1 Answer
  • Posted on Jun 04, 2013

SOURCE: dewalt dc925 chuck is stuck closerd with a hole

We had a dewalt keyless with a bit in it and stuck from where I had gotten it wet. WD-40 did not help.Sprayed PB Blaster in an around the chuck, let it sit for 30 minutes. One good twist with channel locks opened it right up.

beatrixtuffy

Beatrix Tuffy

  • 49 Answers
  • Posted on Jul 03, 2013

SOURCE: my drill bit has stuck in the chuck of my dewalt

I don't think that now your drill machine is in running condition. So, I would like to suggest you that you must be buy new one drill machine. And, if you are looking for any proper source for that so here you can get Dewalt drill machine.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How do I get a stuck bit out of my DeWalt dc 895?
https://www.youtube.com/watch?v=pNDgV_6k12E
Reverse and Forward Mode: Try putting the drill in reverse mode and hit the trigger, then forward mode. If that doesn't work, tap the tip on the driveway but don't slam it. It should release .

Use a Wrench: First, make sure that the chuck is in the locked position. Next, use an allen wrench to loosen the set screw on the side of the chuck. Finally, unscrew the drill bit from the chuck .

Remove Chuck Collar: Use a wrench or pliers to loosen the chuck collar and remove it from the chuck. Then, use a screwdriver or other tool to remove the chuck jaws and any other components that may be blocking access to the stuck drill bit. Once these components are removed, you should be able to access the drill bit and remove it from the chuck .
Read full answer
Oct 29, 2023 • Dewalt Drills
0helpful
1answer

How to remove bit it's stuck and not moving
Drill bit? If it's stuck in a piece of metal try drilling from the other side and then knock it out use a maller drill bit.

Stuck in metal, use vise grips to grab it and turn counter clockwise

Stuck in drill chuck? Get a key for the electric drill. Battery operated, use a par of pair of channel lock pliers to open the chuck.
Read full answer
Oct 30, 2018 • Cars & Trucks
0helpful
1answer

Removing the drill bit from the chuck.
Very often, a certain size of drill bit can get "swallowed " by the drill chuck.
It has happened to me often.
I recommend you insert the drill bit into a vise and tighten it well, leaving a 1/8 inch gap to the chuck.
Take a large screwdriver and pry the chuck away from the vise.
It should come out.
God bless your efforts.
Read full answer
Jul 02, 2018 • Drills
0answers

How do you remove a stuck bit in the chuck of a TE 17 Hilti hammer drill?
Read full answer
Be the first to answer Jun 12, 2018 • Hilti Drills
0helpful
1answer

Bought a Bosch Drill. Chuck packed up after five months. Mega Mica Eastgate say chuck not covered?? Bought 2015/12/19 08:57:22 for R2999.00
not much can be done if the dealer will not warrant the chuck
if the bosch name appears on the chuck, call bosch direct and make a complaint but if it doesn't then get a new and better quality chuck and replace the chuck on the drill
remember that ordinary key operated 3 jaw chucks are not designed to used in a hammer operation continuously as that damages the screw mechanism of the chuck especially if the drill bit is over 5/16 drill size
if that is your operation, invest in a special masonry drill such as ramset or hilti or other makes of that sort
Read full answer
May 30, 2016 • Bosch Drills
0helpful
1answer

How to remove bit stuck in kango drill
Hello, You might try spraying some wd-40 in the chuck to let soak and loosen up, to be able to turn and remove the bit.
Read full answer
May 15, 2014 • Drills
0helpful
1answer

Drillbit stuck
Can not see what model you have. Is it a keyless chuck or an SDS chuck? With a keyless chuck hold the machine in a vice by the drill bit. now tap the chuck with a hammer or pin punch & hammer. DONOT hit the chuck on the jaws gut on the rim around them. I have had success using this method. If it is an SDS type chuck pull the chuck cap up as far as possible along the bit them if there are any ring springs you will have to try remove them then slide the sleeve up the bit, now you should be able to remove any steel balls. If the bit does not come out now hold bit in vice as before and tap on tool holder.
Read full answer
Mar 02, 2014 • Bosch Drills
1helpful
2answers

Need a manual for Ramset Dyna drill 321 (Hammer) Have a Ramset Bit stuck in the chuck. Chuck seems to be enclosed unsure how to remove or open chuck to remove bit. Drill bit is Ramset.
take flat head screw driver put flat head driver in to gears on chuck hit screw driver with hammer counter clock wise
Read full answer
Nov 10, 2010 • Garden
0helpful
1answer

I have a broken drill bit stuck in a B&D BD154R chuck It is broken off low down so I can't get a pair of pliers on it. What can I do?
If it won't fall out with the chuck fully open, you'll have to remove the chuck. use an allen wrench larger than the jammed bit and lock it into the chuck. Hit the allen wrench with a soft hammer to loosen the chuck. Remove chuck completely and push the bit out from the bottom.
Read full answer
Mar 09, 2010 • Garden
2helpful
1answer

How do I remove an SDS bit stuck in a B&D SDS
the rubber cap in the sds chuck nose is only snap tight try to remove and dismantle the retractable locking pins.
Read full answer
Nov 26, 2009 • Drills
Not finding what you are looking for?

View Most Popular

DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver

  • Drills

Related Question

How do I get a stuck bit out of my DeWalt dc 895?

  • Dewalt Drills

993 views

Ask a Question

Usually answered in minutes!

Popular Questions

Broken dewalt battery 18v lithium ion

Dewalt DC920KA Heavy Duty Xrp 18V...

Dewalt battery charger won't charge

Dewalt DW056 18 Volt Cordless Impact...

My charger displayed cold/hot pack

Dewalt DC920KA Heavy Duty Xrp 18V...

Jaws won't tighten or loosen to hold a bit

Dewalt 18v Battery Hammer Drill...

Charger light blinks rapidly for dewalt charger?

Dewalt Drills

Top Dewalt Drills Experts

Cindy Wells

Level 3 Expert

6688 Answers

Brad Brown

Level 3 Expert

19187 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

Are you a Dewalt Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
Manual. user-manual-DC920KA Heavy Duty...

DC920KA Heavy Duty...

Loading...