Samsung reset codes

start by trying to reset your TV. Disconnect the power cord from the outlet, then press and hold the power button on the TV (not the remote), for at least 10 seconds. Then wait a few minutes and plug the TV back in and press power once. 2 blinks on Samsung TV's usually indicates a bad power supply

start by trying to reset your TV. Disconnect the power cord from the outlet, then press and hold the power button on the TV (not the remote), for at least 10 seconds. Then wait a few minutes and plug the TV back in and press power once. 2 blinks on Samsung TV's usually indicates a bad power supply
https://www.samsung.com/nz/support/tv-audio-video/troubleshooting-sound-issues-on-your-samsung-tv/

start by trying to reset your TV. Disconnect the power cord from the outlet, then press and hold the power button on the TV (not the remote), for at least 10 seconds. Then wait a few minutes and plug the TV back in and press power once. 2 blinks on Samsung TV's usually indicates a bad power supply.Sep 21, 2017

Press the MODE button to make the TV
indicator on the remote control flash.
2 Press POWER button to turn on the TV.
3 Point the remote control toward the TV.
4 While holding down POWER, enter the code
corresponding to your brand of TV.
• If the code matches the TV's code, the TV will be turned off.
• If there is more than one code listed for your TV in the table,
enter one at a time to determine which code works.
Example: For a Samsung TV
While holding down POWER, use the number buttons to enter 00,
01, 02, 03, 04, and 05.
• You can use the POWER, TV/VIDEO, VOLUME, CHANNEL, and
Numeric buttons (0~9).
5 Pont the remote control toward the TV and press
POWER. If the TV turns off or on, the setting is
complete.

It is helpful to have the sequence of the blinking red light. This may help:

MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927

Page 43

3. Error Code Operational Check

Note: The TV must be in "Shut Down" and not have been switched Off, to perform the Error Code Operational

Check. When the TV is switched Off, the code automatically resets to "12" No Error.



Pressing the front panel "DEVICE" and "MENU" buttons at the same time, and holding for 5 seconds,

activates the Error Code Mode. The LED flashes denoting a two digit Error Code, or indicating no problem

has occured since the last Initalization.



Note: The front panel buttons must be used, NOT those on the Remote Control.



• The number of flashes indicates the value of the MSD (tens digit) of the Error Code.

• The flashing then pauses for approximately 1/2 second.

• The LED then flashes indicating the value of the LSD (ones digit) of the Error Code.

• The Error Code is repeated a total of 5 times.



Example: If the Error Code is "23", the LED will flash two times, pause, and then flash three times.



4. Error Codes

The Error Code designations indicating malfunction, or no malfunction, are listed below:

POWER

LED

STATUS

LED

LAMP

LED

Power

Status Condition

Off Yellow Off Low

Power Excess heat. Check Lamp Filter

Off or On Off Yellow No

change

120w usage time over 7000 Hrs.

150W usage time over 3500 Hrs.

Off Off Blinks

Yellow

Low

Power Lamp Cover open

Off Blinks

Yellow Off " Filter Cover Open

Off Off Red Stby Lamp did not turn On

Off Blinks

Red Off Low

Power Fan Stopped

Off Red Off " Circuit failure (short or DVI

connector unplugged)

Abnormal LED Indications

Error Codes "DEVICE" & "MENU"



Error Codes Description



12 No error detected

22 Recovery from Reset

32 Lamp cover is Open

34 Lamp abnormality

35 DM Fan failed (Chassis Fan)

36 Exhaust or Lamp Ballast Fan failed

37 DMD Engine Fan failed

38 Lamp temperature abnormally high. Remove Lamp to check filter.

39 DMD temperature abnormally high

41 Short is detected (Standby Power Supplies)

42 Lamp Fan failed

44 DVI cable between Format and Engine disconnected

46 DMD Temp. Sensor not detected (check DT connector))

47 DM Temperature too high

48 Engine power supply short detected

51 Speaker Drive circuit short detected

52 HDD excess temperature (V30+ & V31 only)

55 HDD Fan Stopped (V30+ & V31 onlyt)

A blinking yellow for this model indicates the TV is too hot, unplug & allow 30-45 min to cool before re-plugging .
OR: lamp not installed or lamp door not closed. there is a lamp door switch that may not be closing, simulating door not closed

LED Indications

The front panel Status LED provides an indication of

the set's operation and the possible cause of a malfunction.

If an abnormal condition is indicated, perform the

Self Diagnostics procedure.

Self Diagnostics

To activate, press the front panel <ACTIVITY> &<CH

??> buttons at the same time and hold for 5 seconds.

The STATUS LED will then flash denoting a two digit

code.

• The number of flashes indicates the value of the

MSD (tens digit) of the Error Code.

• The flashing then pauses for approximately 1/2

second.

• The LED then flashes indicating the value of the

(ones digit) of the Error Code.

• The Error Code is repeated a total of 5 times.

Example: If the Error Code is "23", the LED

will flash two times, pause, and then flash three

times.

Table 2-2: LED Indications

Error Codes, descriiptions and the most likely cause of

the error are listed in Table 2-3.

Note: The TV must be in "Shut Down." The LED

will probably be indicating an abnormal

condition. If the TV is switched Off, AC is

removed, or a System Reset is performed, the

code automatically resets to "12" No Error.

See the Error Code Log to retrieve a history of

errors.

Note: Use the front panel buttons, not the remote

control.

Note: If there is no response, the front panel may be

locked by a V-Chip setting. To unlock, press

and hold <ACTIVITY> on the front panel for

8 seconds.

LED Indication Condition

Off Off (standby)

Green Power On

Slow Blink Green Power Off with Timer Set

Fast Blink Green (80 seconds) > Off Power Off (Cooling fan still working, 80 sec)

LED Indication Condition

Red Lamp Failure

Yellow TV Too Hot

Slow Blink Red TV May Require Service

Slow Blink Yellow Lamp Door Open or No Lamp Installed

NORMAL INDICATIONS
ABNORMAL INDICATIONS (For details perform Self Diagnostics Procedure.)

Hello

Four digit universal remote control codes for Samsung TV/VCR combo are:-
0358 0942

Direct Code Entry

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

NB: Switch OFF, wait ofr 3 seconds or more, and switch ON your system with its front panel power control each time before trying an other code.

Hello

Do the following steps first, and find whether you could unlock your TV or not. If can't, follow the rest.
Steps To Unlock A Samsung TV 1. Turn the power off.
2. On the remote, press Mute followed by 1, 8, 2, Power in sequence.
3. You should now see the service menu. To exit the Service Menu always select RESET.


Three digit universal remote code for Samsung are:-

004/ 005/ 009/ 015/ 104/ 105/ 106/ 109/ 133/ 172

Four Digit Universal remote code for Samsung are:-

0105 0077 0076 0109 0007 0009 0004 0005 0085 0172 0942 0358 0012 0015 0080 0104 0106

Direct Code Entry

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

Code Search If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.

1. Manually turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
5. Press and release MUTE to install the code. The indicator light goes off.

Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.

Automatic Programming
1. Turn off the device with which you want to use the remote control.
2. Press and hold the corresponding button on the remote control (TV, VCR, SAT, DVD) until POWER INDICATOR illuminates. The remote control is in programming mode.
3. Press POWER button on remote and release . The POWER INDICATOR flashes once and stays on indicating the unit is in Power scan mode.
4. Press CHANNEL+ or CHANNEL- repeatedly until the device turns on.
5. When the device turns on, press ok to store the code.

Here's the basic troubleshooting:

1. Make sure that no front panel buttons are inadvertently stuck in an "engaged" position.
2. Disconnect ALL devices from the TV.
3. Press the SYSTEM RESET button and hold for 10 seconds. Proceed if the problem still exist.
   
4. Press and hold POWER and MENU buttons simultaneously for 20 seconds. Proceed if the problem still exist.
5. Unplug the TV from it's power source for various times, ranging between 5 minutes and 24 hours.
6. If it still shuts down, press the DEVICE and MENU buttons on the front panel simultaneously and hold it for 5 seconds to activate the Error Code Operational Check. The status LED indicator will then flash denoting a two digit code.
   
7. Count the number of flashes then pauses for about a half second then flashes again. The first number of flashes indicates the first digit of the error code and the second number of flashes indicates the second digit of the code. For example, if the error code is "35", the LED will flash 3 times, pauses, then flashes 5 times. The error code is repeated a total of 5 times.

Please let me know the code you got and I'll tell where the problem lies and how to fix it.