Where can I find parts for the kango 900s breaker

The carbonbrushes if they are short and you will replace them there is a long brown wire on one of the 2 brushes thats goes inside the handgrip but be careful there are 2 plastic pieces for the power licht and the carbon brush is on a electronic modul inside the handgrip by a sliding contact 90 degrees beware also on the black damping rings inbetween the machine and handgrip 4 pieces to protect vibrations . if you have open the handgrip i will say that you allways control the bearing at the end of the armature because its a very to small choosen bearing that is oft in bad condition i mean it , if it has its operating hours if the carbon brushes are short.but the handgrip must be opened for remove the brushes.

Its the ask if its a MILWAUKEE kango 900K yes but if its a KANGO 900K the metal red or metal blue demolitionhammers its difficult to find but the cause of the broken con rod when the machine is not good air tight it can have has burned o-rings and more also the battle cilinder can be torned and piston pin not smooth enough and ,more parts of the original English KANGO are not simply deliverable anymore, but for the American milwaukee red 900k its not a problem
http://services.milwaukeetool.nl/jsp/material.jsp#part0239

If these are the original Kango kangos then you are out of luck. They have been obsolete for many years now and no parts have been manufactured for a long time. The name was bought by DeWalt and they didn't do much with it. The Kango name is now ownd and used by Milwaukee, but there machines do differ alot from the originals. There were a few main models and the main mid sized breakers were the 900 (hammer only) and 950 (rotary hammer) There were a few facelift/variations of each (K, X and B I think) and they did use a couple of different sized seals/pistons/cylinders.
If it is one of the Milwaukee models you can look up diagrams here...
http://www.milwaukeetool.com/

Hi and welcome to FixYa. I am Kelly.

Most of the 900S models are listed as 240VAC models so I have used maybe a rash assumption that this unit is outside of the USA.

There are 2 different models of the 900S however the owners manual is the same: (2.19 mb)
http://www.milwaukeetool.co.uk/int/int_opmanual.nsf/vwOMLink/289%20739%20-%20900%20SDSMAX.pdf/$FILE/289%20739%20-%20900%20SDSMAX.pdf

Parts on the other hand go by an HF-number.

http://www.milwaukeetool.co.uk/int%5Cint_opmanual.nsf/vwSparePartsSearchResults?OpenView&ExpandView=1&nav1=ps&Count=30&StartKey=900S#

The next 3 links are used together: Picture is .gif
http://www.milwaukeetool.co.uk/int/aegexplo2003.nsf/FilesMET/417158.gif
IPL part numbers:
http://www.milwaukeetool.co.uk/int%5Cint_opmanual.nsf/0/6D282A18A561C0D9C12578AA00392977?OpenDocument&nav1=ps

http://www.milwaukeetool.co.uk/int%5Cint_opmanual.nsf/0/C7621BBE76DD8313C12578AA00392997?OpenDocument&nav1=ps

MILWAUKEE ELECTRIC TOOL
MAX-EYTH-STRASSE 10
D-71364 WINNENDEN
GERMANY
Phone: +49 71 95 12-0
Fax: +49 71 95 12-666

Milwaukee Tool
MEDINA HOUSE, FIELDHOUSE LANE
BUCKS - SL7 1TB MARLOW
GREAT BRITAIN
Phone: +44 (0)1628 894400
Fax: +44 (0)1628 894401

Thanks for choosing FixYa,
Kelly

I can ouly locate the Kango 900 S. Error in the model number last digit maybe? You can to to this link:
http://www.milwaukeetool.co.uk/int/uk/uk_opmanual.nsf/frmSparePartsSearch?OpenForm&nav1=ps
and then select 900S to download the manual.

Or maybe just use this direct link:
http://www.milwaukeetool.co.uk/int/int_opmanual.nsf/vwOMLink/289%20739%20-%20900%20SDSMAX.pdf/$FILE/289%20739%20-%20900%20SDSMAX.pdf

Let me know if this manual did not work for you and I will look again.
Thanks for choosing FixYa
Kelly

Google KANGO for a dealer in your area.

Not all parts are available.

Good luck.

What kango hammer do you have? I am most familiar with the UK kango 900 and 950, pre-milwaukee.

The 900 is a hammer only, the 950 is a hammer drill. the newer ones 950s used spline bits. Unfortunately new parts are no longer available for these great machines. What is your problem.

\charlie use sewing machine oil, as for a book on it put the make model into google and a pdf might be available as for parts not really unless you sroce them through the paper or ebay

Milwaukee now owns Kango, unfortunately I believe the 950sv is the old style. Parts are no longer avail. I have about 20 of the breakers. It is really too bad, they were great machines.