Question about Fisher and Paykel GWL11 Top Load Washer

Open Question

How do I clean the filter

Hot temperature light keeps coming on machine is peeping and there is no water flow

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
stephanos18

Steven White

  • 144 Answers

SOURCE: Fisher Paykel GWL11 Cold Water Not Flowing

you can swap the hot and cold valves over and see if this fixes the problem as it sound like your cold valve is faulty but not the hot valve.

Cheers

Posted on Mar 25, 2009

Ad

Azrael SRL

  • 11800 Answers

SOURCE: cold water not flowing into machine.But ok coming

Check the intake valve, most likely it was blocked by concretions.

Posted on Jan 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does the F19 error code mean


For Bosch and Neff washing machines, the F19 error means that the incoming water did not reach the desired temperature in the 'normal amount of time'. This could be due to a fault with the heating system, the sensor, or the communication between the sensor and the main control board.

The issue could also be due to insufficient hot water reaching the washer. Check that the inlet hose isn't kinked and that the hot water shut-off valve is open. Close the valve and remove the hose. Check and clean the filter at the washing machine inlet. Clean or replace the filter at the shut-off valve. Replace the hose only on the shut-off valve and place a bucket underneath it. Open the shut-off valve and check the water flow. Replace the hose if there is limited flow. (Some anti-flood hoses restrict the water pressure when they detect a small leak.) If you do not have good water flow with a new hose, check the flow from the valve itself. Replace the valve or fix other plumbing issues causing the restricted water flow.

If sufficient hot water is reaching the machine, then you have to find the fault in the heating system. If the washing machine is under warranty, contact the manufacturer. If you would like me to search for any available parts diagrams, please add a comment with the model number of the washer.

I hope this helps.

Cindy Wells

May 26, 2018 | Washing Machines

4 Answers

How do I unblock filter of washing machine


Turn of hot tap and disconnect hot water hose from inlet solenoid, using long nose pliers pull out filter from solenoid.
The problem may well be the solenoid needs replacing as they do tend to fail occasionally.

Oct 10, 2014 | Fisher and Paykel GWL11 Top Load Washer

2 Answers

Error code of NF (no fill) on samsung top load washer (WA422PRHDWR/AA) even after checking lines for restrictions and ensuring clean line filters (red and blue). Now, when it does work, it will only do a...


Put the temp select switch on HOT, start machine. If water comes out check the flow amount. If no water flow, replace inlet water valve. If there is water flow switch to COLD, start machine. If water comes out check the flow amount should be approximately equal or slightly more than flow on HOT. If no water flow, replace inlet water valve. Move selector to WARM, start machine. Now there should be twice the flow of water than there was with HOT and COLD temps. I suspect it is the HOT side of inlet water valve that has failed because machines usually rinse with COLD water.

Jan 20, 2013 | Samsung WA422PRHDWR 4.2 Cu. Ft. VRT Top...

1 Answer

Rheem rte13 standby (green) light not on


You might have crossover problem caused by bad faucet cartridge.
http://waterheatertimer.org/Crossover.html

The green standby light should come on when 240Volt power is applied. Page 6 manual.
Both red lights should come on when tankless is activated. Page 6 manual

RTE 13 requires 60 amp breaker and 6 gauge wire
http://waterheatertimer.org/How-to-wire-Tankless-electric-water-heater.html
http://waterheatertimer.org/pdf/Rheem-TanklessElectricUC_AP15447.pdf

Factory temperature setting is usually default 120 degrees.
Adjust temps page 11 manual
Thermostat calibration is always approximate.
120 degrees is not hot enough to burn the skin.
Exceptionally cold incoming water temperature can cause tankless not to heat enough hot water: install tempering tank to preheat water to room temperature.
Tankless cannot be exposed to more than 11 grains hardness in water. Delime tankless yearly, clean water filter monthly, do not install low-flow restrictions or conserve water since the flow rate must remain high for tankless to activate.
Rheem does not post service manuals for their tankless water heaters.
Call Rheem 800 432-8373

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Aug 05, 2012 | Rheem Tankless Hot Water Heater...

1 Answer

Fills with water and then stops and beeps and won;t continue. The hot and cold water buttons are flashing. Waterr starts trickling in and it is slowly spinning but doesn't seem to agitate


Hi just read your posting.The 2 lights that are flashing means your machine has not detected any water level difference.1st turn off both hot and cold taps and 1st remove the cold inlet hose from the machine end,Put the end of the hose into a bucket and turn the tap on.You should get a good flow of water.If you do not get a good flow of water then remove the tap end of the hose and see if you are getting water out of the tap.Check the inlet filters on both ends of the hose to see if they are blocked.If they are blocked clean them with a brush.Check also the water valve end where the hose connected to the machine to see if this filter is blocked. Once you have water coming out of the hose and all the filters are clean refit the hose and repeat to the hot hose.Now select a cycle and push start.If the water flow is good then the machine will work properly.If you still get slow water even when you have good pressure coming out of the hoses then your water valves are faulty.Please reply on how you got on and for further advice.looking forward to your reply.

Sep 21, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

My bosch washing machine has taken to only allowing washing at 30 degrees. When a higher temperature is requested, no water flows into the machine. Any ideas why?


Clogged/defective/burnt out hot water valve. Disconnect hot water hose and clean the filter in the valve inlet. If this did not help, check if there is power to the hot water valve when it's supposed to fill. If there is power, but no water is coming into the washer - replace the valve.

Apr 10, 2010 | Washing Machines

1 Answer

Does not clean


Hi

If your dishwasher is cleaning poorly, check these:

Water-inlet valve Most cleaning problems are caused by the dishwasher not getting enough wash water, so the water-inlet valve is often to blame. This valve is usually at the bottom left or right of the dishwasher, behind the lower access panel. It's the device with the main water line from the house, a rubber tube to the dishwasher, and two wires attached to it. 

When a water-inlet valve is defective, you may hear the sound that's usually referred to as "water hammer." If the water-inlet valve is defective, you need to completely replace it. 


Internal filters Every dishwasher has some type of filter to keep large food particles and foreign objects away from the pump assembly:

  • Most modern dishwashers have self-cleaning filters that don't need any routine cleaning.


  • Some have filters in the bottom of the dishwasher that you need to periodically clean. You don't need any tools to remove the filter, and cleaning it is easy. Consult your owner's manual to determine which type you have and its maintenance requirements.


If your filter is clogged, it may be causing the cleaning problem. 

Drain valve Some dishwashers have a valve (or gate) that should open only during draining. If debris lodges in the valve, it can't close properly, so water drains out during the wash cycle. Most dishwashers drain into the garbage disposer. If yours does that, listen for water flowing into the disposer during the wash cycle. If you can hear it then, the drain valve may be clogged.

Spray arms There's a spray arm at the bottom of your dishwasher--it may have a tall spray tube mounted to the center of it. There may also be a spray arm located directly beneath the upper rack of dishes and/or above the upper rack.

If debris is blocking the holes in the spray arms where the water comes out, it could cause cleaning problems. Regularly inspect each of the spray arms and clean out the holes as necessary. 

Water temperature To get the best cleaning results, the water entering your dishwasher needs to be hot enough. Try running the hot water in your kitchen sink for about 30 seconds before starting the dishwasher, to pre-heat it. Also, if your dishwasher lets you select a higher wash or rinse temperature, try that to see if it helps. 

To check the temperature of the hot water that comes from your kitchen faucet use a waterproof thermometer. If the water isn't 120 degrees Fahrenheit, your dishwasher may have trouble getting your dishes clean. You could increase the temperature of the hot water to the whole house--and therefore the dishwasher--by adjusting the hot water heater thermostat.

Warning! To lessen the risk of scalding, don't set the hot water heater temperature higher than 120 degrees Fahrenheit. 

Detergent cup Dishwashers don't perform their best if detergent is introduced only at the beginning of a cycle, so add detergent to both parts of the cup. 


Please do rate the solution as FixYa and revert for further assistance.


Thanks
Rylee


Apr 08, 2009 | GE Tritonr XL GSD6260JCC Dishwasher

2 Answers

Hotpoint WF250 - clothes largely dry and covered in powder


check to make sure the water inlet filter is not clogged with debris.
turn off water and disconnect at washer , look in opening is filter screen clear, some are removable to clean others you have to brush etc....
there are two more places to check but they are inside the washer at the water control solenoid and the inlet , the water pressure sensor may have something to do with this issue.
best to open the top and listen and watch. (3 screws in rear top)

Apr 06, 2008 | Hotpoint Aquarius WF000 Front Load Washer

2 Answers

Error code F24


I see the same problem and now that I know it's a water temp sensor, I really don't have a problem. Living in Houston it get's so hot the cold water is hot coming through the pipes. I didn't have this error 24 until summer...

Nov 18, 2007 | Kenmore 46462 Front Load Washer

Not finding what you are looking for?

Open Questions:

See all Fisher and Paykel GWL11 Top Load Washer Questions

Fisher and Paykel GWL11 Top Load Washer Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...