Kodak EasyShare CX7330 Digital Camera Logo
A
Anonymous Posted on Oct 15, 2014

Top of camera atoff setting, the outer case is seperating

The main case is pulling apart

×

1 Answer

David Payne

Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

  • Kodak Master 14,162 Answers
  • Posted on Nov 24, 2014
David Payne
Kodak Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

Joined: Dec 27, 2008
Answers
14162
Questions
0
Helped
2998497
Points
455836

IT WOULD PROBABLY BE CHEAPER TO JUST PURCHASE ANOTHER CAMERA. EBAY IS SELL THE SAME CAMERAS FOR UNDER 20 DOLLARS.

SOURCE: http://gethuman.com/phone-number/Kodak/ Kodak Phone Numbertop of camera atoff setting, the outer case is sep - a-d-12.png Home > Find a Phone Number > Kodak Phone Number
You can call Kodak at this number, but it's not the best way to reach them. This phone number was voted the best of all phone numbers, but not best overall. Click here to find the best way to contact Kodak


Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How do I remove a pull chain socket from the outer bell of an antique pan light?

Some older sockets had a small recessed set screw on the socket which connects to a shaft. The very old models which were 3 way (very large base bulb) had a porcelain socket. There's no set screw on those sockets. They just unscrew from the threaded shaft.
Oct 18, 2014 • Dryers
0helpful
1answer

Cant get the case to seperate on a 1997 gsxr 1100.

have you removed the clutch assy gear as there may be a plate with bolts on either side of casings ! bolts on top and bottom side ov cases out ? if all out then there are places to hit with hard mallet and pri with levers , there are several dowels to connect cases in place and sealant !
0helpful
1answer

How do I seperate motor from generator

on the rear of the generator there is a bolt in the center remove that bolt then remove the brushes then the outer bolts from the generator case then pull it apart
0helpful
1answer
1helpful
1answer

Replace transfer case chain in a 1989 GMC K2500

its not hard to do you need a gasket and seal kit too the hardest part is seperating the case halves . do not place a screwdriver in the case halves to seperate you will cause a leak ! remove the nuts on the yokes first then the case . mark with a scribed line and remove the trans speedo cable assembly set it aside tap and pry the case halves apart pull off the back half of case the front half is where you want everything to stay in place try to keep it standing up so rear case is up then you can lift up the front output shaft the chain and the planetary remove the rest of parts install new seals and reassemble the case uses rtv black sealant instead of gasket
1helpful
1answer

Will not spin

The drain line is probably clogged. Maybe that a sock or other piece of clothing get between the clothes tub and the outer tub that holds the water. In this case it may then get into the drain hose that's attached to the pump.Remove the hoses from the pump and pull the item out. In case it clean there, check the outer tub port- open the washer's main access panel and remove the large-diameter rubber hose that connects the pump to the bottom of the outer tub. Then,try to remove the clothing through the port.
0helpful
1answer

I have a top loading kenmore 70 series washer. It

The drain line is probably clogged. Maybe that a sock or other piece of clothing get between the clothes tub and the outer tub that holds the water. In this case it may then get into the drain hose that's attached to the pump.Remove the hoses from the pump and pull the item out. In case it clean there, check the outer tub port- open the washer's main access panel and remove the large-diameter rubber hose that connects the pump to the bottom of the outer tub. Then,try to remove the clothing through the port.
15helpful
4answers

How to repair broken hinge of my Verizon LG Vx8350

I was able to take apart a VX8350 I have with a broken screen. I don't see any way to replace just the hinges with replacing the whole top part of the phone including the screen. The ribbon cable from the screen runs through the hinge part into the main assembly of the phone. It appears the cable can't be removed without cutting it.
0helpful
1answer

Panasonic Lumix DMC-TZI - broken battery tab and battery/card door

well there is no easy way. You will have to open the machine up when you have ordered the parts you needed. Not to hard but make sure you keep you eye on the sequence how you pull it apart.
Not finding what you are looking for?

107 views

Ask a Question

Usually answered in minutes!

Top Kodak Cameras Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Are you a Kodak Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...