At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
A Netware error was detected. Please verify that you are properly logged in. See the network Installation guide for more information. It shows when open PM5
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If your F35-WQXGA Barco projector is showing a critical error at startup with an IP address, here are a few steps you can try:
Check the IP address: Ensure that the IP address is correctly entered and that it matches the IP address assigned to the projector. You can verify the IP address by checking the network settings of the projector.
Check the network connection: Ensure that the network cable is properly connected to the projector and that the network is properly configured. You can try connecting a different device to the network to ensure that it is working properly
Check the projector's logs: The projector may log errors and events that can provide more information about the issue. You can access the projector's logs through the projector's web interface or by connecting to the projector through Telnet or SSH.
Check the network settings: Ensure that the projector's network settings, such as the IP address, subnet mask, and gateway, are correctly configured. You can check the network settings through the projector's web interface or by connecting to the projector through Telnet or SSH.
Check the network connection: Ensure that the network cable is properly connected to the projector and that the network is properly configured. You can try connecting a different device to the network to ensure that it is working properly.
Check the firmware: Ensure that the projector's firmware is up to date. You can check for firmware updates on the Barco website or by contacting their support team. You can also try reinstalling the firmware to ensure that it is not corrupted.
Perform a factory reset: A factory reset can reset the projector to its default settings and may resolve the issue. You can perform a factory reset through the projector's web interface or by connecting to the projector through Telnet or SSH.
No water detected entering machine or Pressure switch trip not detected.
If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash.
If there is no water in the unit: 1. Make sure that both valves at the water source(s) are turned on all the way. 2. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves 3. Verify inlet valve operation
If there is water in the unit: 1. Verify Drain pump operation 2. Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch
Verify there is not a siphon problem
Verify wire harness connections to:Inlet Valves, Pressure Switch, Drain Pump, Flow Meter, and Central Control Unit (CCU)
Check all hoses for possible leaks
Verify pressure switch operation
Verify flow meter operation
Verify CCU operation
OR it could mean
Motor Control Unit (MCU) Heat Sink Thermal Trip If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink which will stop motor functions and an "E10" will be displayed
Check for Proper Installation, verify the unit is not located near a source of heat and has proper ventilation.
Check Wire Harness connectors to the MCU, and Central Control Unit (CCU)
Check the Drive system for any worn or failed components
Hi,
To resolve the problem , you would have to unistall client for netware protocol.
1.Click start>Click on RUN> Type ncpa.cpl and click on ok
2. Network connections window would open
3. Right click on Local area connection
4. Left click properties
5. Uncheck the box next to Client of netware
6. Click ok and restart your computer
Hi, You need to log on to your router/s and look at the log.
You should also change your security settings in your router/s so this won't happen again.
There's a lot of information, here, so read through everything thoroughly. This is one of those tricky problems that may have several causes. I hope this helps you. If you require addtional assistance, please let me know.
Go to Internet Connections and right click on your internet connection icon. Click on Properties and then Networking. Uncheck Client Services for Netware.
For Fast User Switching go to Control Panel, Administrative Tools, Services and disable Fast User Switching.
I am not sure if you will be able to install Novell Netware 4.11 on this platform. Howver, please see the following link for the BroadCom BCM5721 drivers.
Netware is a very complicated operating system so the manual may not help if you don't have other Netware experience. Nevertheless, Network 4.1 documentation can be found at
http://www.novell.com/documentation/nw4/docui/index.html
×