At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Re: The kitchen aid mixer speed # 10 turns off when using...
The cases need to be split and the lever needs to be fixed so that it grips the notches that hold it in place. It may be a bent lever or a loose pivot screw.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
There are several potential reasons why your KitchenAid dough mixer might be shutting off. Here are a few possible causes:
Overheating: If the mixer has been running for an extended period of time, the motor may overheat and shut off as a safety precaution. In this case, you should allow the mixer to cool down for a while before using it again.
Faulty wiring: If the mixer is shutting off when you turn it on or when you change the speed, there may be a problem with the wiring. You should check the wiring to see if there are any frayed or damaged wires that could be causing the issue.
Clogged air vents: The mixer may shut off if the air vents are clogged, as this can cause the motor to overheat. You should check the air vents to make sure they are clean and unobstructed.
Failed motor: If none of the above issues are present, the problem could be with the motor itself. A failed motor can cause the mixer to shut off, and it may need to be replaced.
If you are not comfortable troubleshooting the mixer yourself, you should consider contacting KitchenAid customer service or a professional appliance repair service for assistance.
Are you engaging the head lock during operation? if not that is why it is loose. If you are it is not uncommon for the head to move around a little under heavy loads, when I make bread the head is always trying to come up so I have to use the head lock switch whenever I use the mixer on bread. It is the only time I lock it down.
you need a new speed control board, easy fix about $35.00 for the part and an hour of your time, not even messy to do a total of six screws and four wire connections that clip on, several youtube step by step instruction videos available. parts available on ebay. let us know if this helps you
You need to adjust the mixer speeds. Obtain a copy of the KSM150 Repair Part List from
Kitchenaid.com. Remove the screw holding the End Cover and locate the three screws from
the Control Plate. All three (2 top left and right, and 1 bottom) must all be adjusted.
1. Loosen the lock nuts enough & Turn the 2 top screws clockwise until they cannot be turned anymore. Leave the bottom screw alone for now. 2. Use a dab of white paint or paper whiteout to mark the positions of the Phillips screws. 3. Plug in your mixer and Set the speed selector to "Stir". 4. Turn each top screw One full turn couterclockwise (alternating between Left and Right) Keep making one full turn at the time (for both left and right) until the motor starts running. 5. Put your hand near the Agitator shaft and allow it to brush your finger slightly. Use your watch or clock and start counting the number of times the shaft touches your finger in 60 seconds. The correct count should be 60 RPM (Rounds Per Minute). If it is less or more than 60, give each screw 1/4 turn counterclockwise or clockwise and start counting again. Now tighten both lock nuts. 6. Set the speed selector to "6" and turn the bottom screw either clockwise or counterclockwise to achieve a speed of 180 RPM.
For your reference, the planetary RPM's for the 5-qt. tilt-head Artisan Stand Mixer are as follows: Stir speed - 60 Speed 2 - 95 Speed 4 - 135 Speed 6 - 180 Speed 8 - 225 Speed 10 - 280
Food grade grease is what Kitchen Aid put into the gearbox originally. They do supply it as a spare part if you cannot find it as a non Kitchen Aid part.
It shouldn't do that, and I really doubt there's anything you can do
about it other than to have the defective part replaced. It sounds to
me as though there's a problem with the control mechanism. If the
machine is still under warranty, contact Kitchenaid to see about
getting it repaired or replaced. If not, get the name of a local shop
that repairs Kitchenaid mixers -- from your description of the problem,
the mixer is nearly unless in its current state.
Some of the gears may have broken or slipped off. You'll need t open it up to see why the shaft from the motor will not spin or you will burn out the motor with the power on trying to make it go. It might be a DIY job if you can see an obvious problem like a slipped gear, otherwise take it to a repair specialist.
×