What does ADF document mean? - Office Equipment & Supplies

ADF is an outomatic document feeder on top of the printer. That's where you put paper that you want copies or scans of. See video below.

Hello Sharon,

When a document jam occurs, "J" and "1" will display alternately on the function number display panel of the scanner.Please perform the following:

1. Remove all documents from the ADF paper chute.
2. Open the ADF while pressing down the ADF open lever. If you are using fi-6130 with the imprinter option attached, please open the imprinter and then open the ADF.
3. Remove the jammed papers from the ADF.
4. Close the ADF pushing the center part of the ADF carefully.

If document jams occur frequently, please check the followings:

1. Do the documents satisfy paper specification?

2. Have the documents been jogged?

• Align the edge of documents for stable paper feeding.

• Remove documents with crease or dog-ear.

• Scanning different width of documents may cause skew and result in paper jam.

3. Are Chuter Unit (ADF paper chute),Guide P ASSY (Sheet guide), Feed roller cover (plate guide) and Brake roller cover installed correctly?

4. Clean the Feed rollers, Eject rollers,Plastic rollers, glass surface and paper feeding surface, and see if the error is

resolved.

5. Replace Pick roller or Brake roller, and see if the error is resolved.Check the consumable counter from the TWAIN driver screen or from the built-in Maintenance mode. When the counter exceeds the values, replace Pick roller or Brake roller.
6. If the issue still persists, then you are recommended to contact the nearest Fujitsu service center for further assistance.


Hope the above information is helpful.


Thanks & regards,
ScanCare

whats meaning

Hi!

ADF stands for Automatic Document Feeder and it means the device mounted on top of your pixma that allows multiple pages to be scanned/copied/faxed one at a time automatically.

Now why does it not print? The machine "believes" some document is inserted in the ADF in order to be scanned/copied/faxed, and wants that operation to be completed before it accept any print job. Please remove, if present, any paper from the ADF. Maybe its only some small piece of broken paper or even dust on the sensor in the ADF.

Good luck!

Hi nigel_lester,

This error message "Document in ADF" that you are getting means that you need to remove foreign object from the Automatic Document Feeder (ADF). Kindly follow the procedure below in clearing document jams:

Document jams in the ADF (Document Tray)

1. First, press Stop/Reset.
2. If a multi-page document is loaded, remove any documents other than the jammed page from the ADF. 3. Then, open the Feeder Cover.
4. From under the roller to the Feeder Cover side, remove the jammed page.
5. If a document is not jammed, check the document feed area if there's foreign material. If there's any, carefully remove it.
6. Close the Feeder Cover.

NOTE:

• If documents remain in the ADF after pressing during scanning, [Document in ADF] will appear on the LCD. Press so that the remaining document is automatically fed out.

• When rescanning the document after clearing the error, rescan it from the first page.

Document jams in the ADF (inner side)

1. Press Stop/Reset.
2. If a multi-page document is loaded, remove any documents other than the jammed page from the ADF, then open the Feeder Cover.
3. Raise the paper release lever (A) then remove the jammed page from under the roller to the Feeder Cover side.
4. Open the Document Cover and pull out the document from the inner side.
5. Close the Document Cover.
6. Close the Feeder Cover.

Note: When rescanning the document after clearing the error, rescan it from the first page.

Hope it helps.

Thank you for using Fixya.

Issue: ERROR LCD: DOCUMENT IN ADF
Solution: Remove foreign object from the Automatic Document Feeder (ADF) - MX310
Check the Automatic Document Feeder (ADF) for obstructions
Follow this procedure to check the ADF for obstructions. You do not need to turn off the power when clearing document jams.
Document jams in the ADF (Document Tray)

1. Press <Stop/Reset>.
   
   
2. If a multi-page document is loaded, remove any documents other than the jammed page from the ADF, then open the Feeder Cover.
   
   
   
   
   
3. Remove the jammed page from under the roller to the Feeder Cover side.
   
   
   
   
4. Pull out the jammed document from the ADF. If the document cannot be easily pulled out, proceed to section Document jams in the ADF (inner side).
   
   
   
   
5. After removing the jammed document or if a document is not jammed, check the document feed area to make sure there is no foreign material. If you find foreign material, carefully remove it.
   
6. Close the Feeder Cover.
   
   Note : If documents remain in the ADF after pressing the Stop/Reset button during scanning, "DOCUMENT IN ADF" appears on the LCD. Press the OK button so that the remaining document is automatically fed out.
   
   When rescanning the document after clearing the error, rescan it from the first page.
   
   Note: The document may not feed properly depending on the media type, or your environment, such as when the temperature and humidity are either too high or too low.
   In this case, reduce the number of document pages to approximately half of the loading capacity. Another alternative is to scan from the platen glass.
   
   

• If documents remain in the ADF after pressing <Stop/Reset> during scanning, [Document in ADF] will appear on the LCD. Press <OK> so that the remaining document is automatically fed out.
  
• When rescanning the document after clearing the error, rescan it from the first page.
  
  
  
  

Document jams in the ADF (inner side)

1. Press <Stop/Reset>.
   
   
2. If a multi-page document is loaded, remove any documents other than the jammed page from the ADF, then open the Feeder Cover.
   
   
   
   
3. Raise the paper release lever (A) then remove the jammed page from under the roller to the Feeder Cover side.
   
   
   
   
4. Open the Document Cover and pull out the document from the inner side.
   
   
   
   
5. Close the Document Cover.
   
   
6. Close the Feeder Cover.
   
   Note: When rescanning the document after clearing the error, rescan it from the first page.
   

Document jams in the ADF (Document Output Slot)
If the document is jammed in the Document Output Slot, pull it out.
Note: When rescanning the document after clearing the error, rescan it from the first page.


Trust this is helpful. Please vote. :)

That means: open adf cover ( auto original feeder ) and remove jamed paper.
Probably adf needs some maintenance, clean rollers.

Hi,

This error message means ADF front side scanning optical alarm (lower optical unit ADF) which indicates ADF (front) lamp intensity check. Please follow the steps provided below:

1. Is the upper glass (white sheet guide)of the reading section dirty?

Open the ADF, and clean the sheet guide (white part) and the glass.
# When operating the scanner, the ADF’s inside glass becomes very hot. Take serious caution as the heat can cause burns. Before you clean the inside of the scanner, turn off its power and unplug the AC adapter from the outlet and wait (at least three minutes) until it gets cold.Be careful not to pinch your fingers when the ADF cover is being closed.
Note: Cleaning should be done approximately every 10,000 sheets scanned, though it may vary depending on types of
documents scanned. More frequent cleaning is necessary when the following types of documents are scanned:
- Smooth surface document such as coated paper
- Documents printed on almost entire surface
- Documents processed with chemical materials such as carbonless paper
- Paper with a high calcium content
- Pages with pencil lead
- Document where toner is not fused sufficiently.

If the above does not help, then the issue is caused by any of the followings for which you may have to contact the Fujitsu Expert/Engineer.

1. Lower Optical unit ADF may be dirty.
2. Lower lamp may not be functioning properly.
3. The connecting cables might be damaged.
4. The connectors are not connected properly.

Hope the above information is helpful.

Regards,

TechSatya

The first thing I always do to a misbehaving ADF is take a dust blaster(canned air) and blow all of the dust and debris out of the ADF,This means lifting the ADF cover and cleaning everywhere.There is always a switch or sensor whose job it is to detect a sheet of paper placed in the ADF.Good Luck.

If the green light on the adf is blinking that means that there is a paper jam in the adf. I sure you know that the copier you are using is at least 10 - 15 years old. Has the adf worked recently? Are one of the adf hings broken? If so, line the adf straight on the top of the copy board glass. There is a magnet that needs to be closed to make the adf work. Try to see if there is any small piece of paper in the papeer path of the adf and use a can of air to blow out the sensors and get back to us.