Question about GE Washing Machines

2 Answers

H2O supply and Tub will not fill in Ge Washer

Posted by Anonymous on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hello I have a top loader washer ge that says h20 supply I have water going in it but can't get it to clear

Posted on Nov 06, 2019

Ad

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • GE Master
  • 473 Answers

First make sure someone didn't turn off the supply valves where the washer hoses are attached to. If both are on, then try to fill machine and switch between hot and cold water. If one of the 2 temps works, the other half of the fill valve is bad. The fill valve is the part where the hoses attach to the back of the machine. It is a 2 part electric valve with 2 electric coils on the valve. Could be one coil is bad or possibly the filter screen is blocked on one side. Screens can be checked and looked at by removing hoses and looking inside end of valve. If coil is bad, complete valve needs replaced. Easy exchange, a few screws, 4 wires, and a small hose leading to inside of machine.

Posted on Feb 28, 2015

Ad

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Anonymous

  • 51 Answers

SOURCE: GE WHRE5260E1WW Washer

The mixing valve needs to be replaced. It should be under $50 and is easy to do.

Posted on Jan 23, 2008

Anonymous

  • 1 Answer

SOURCE: GE Front Load Washer

Removing the lower front panel (3 screws nearest floor), and opening the round, white water pump filter cap (be ready to catch about 2 gallons of water!) is the best place to start. All you need is a Phillips head screwdriver and a large, flat pan (deep turkey tray works well)!

YOU WILL NOT BELIEVE what I found in my filter housing this morning (see photo below)!

490ccb1.jpg

The washer is working fine now, although I may go back and remove the entire water pump so it can be dismantled, thoroughly cleaned, and reinstalled.

Posted on Sep 22, 2008

mgprice

Mike Price

  • 744 Answers

SOURCE: water doesn't stop filling tub and tub overflows

Hello,Sounds like a problem with either the inlet valve or the pressure switch, way to determine which on is while it is filling pull the plug..if water keeps filling it's the inlet valve..if it stops filling it's the pressure switch..If you have any other questions or concerns please feel free to comment again..good luck!! Mike

Posted on Aug 31, 2009

Anonymous

  • 1 Answer

SOURCE: GE WASHER WCXR1070A2WW TUB FILL AND DRAINS NO SPIN,AGGITATE

HUMS WONT START

Posted on Jan 19, 2010

beltronic205

Gerry Harvey

  • 1481 Answers

SOURCE: GE Washer Wont Fill

Make sure drain hose not too low , creating syphon...

Posted on Jun 01, 2010

Testimonial: "After posting this question I saw something on the internet suggesting the same. I think this must have been the problem. Thanks for your help!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a GE spave maker Laundry that fills up with water than stops!


GE Washer Not Agitating Repair Guide

www.appliance-repair-it.com/GE-washer.html
If your washer will not agitate or spin take a look at this page GE Washer Not ... If the washer fills up with water then doesn't do anything at all and you do not hear ... if this were the problem, the water would not stop running, over-filling the tub.

GE washer spin cycle not working - ApplianceBlog

www.applianceblog.com/.../217-GE-washer-spin-cycle-not-working

Mar 12, 2005 - 10 posts - ‎3 authors
I have a GE "Spacemaker Laundry" (Stackable) model number ... Today it filled withwater initially then stopped working all together when it ... Bad motor, something jammed/seized up holding the motor back from running?

Jan 10, 2016 | GE Spacemaker Washer and Dryer Electric...

1 Answer

How do I reset GTWN7450DWWwasher after code H2O supply comes on?


If the water supply valves are open, turn off the valves and disconnect the hoses. Replace the hoses. (You may have flood-prevention hoses. When these fail, the hose actually restricts water flow to avoid flooding.) If you want to test this, try placing a bucket under the inlet hoses and opening each valve in turn. Check how fast the water fills your bucket. Make sure that you cleaned the filters at the washer inlets and at the supply valves.

If the valves were closed, try running the washer with the valves open.

If that doesn't help, the flow meter valve has possibly failed or another part in that system has failed. This is part 805 on the tub and lid diagram here: https://www.geapplianceparts.com/store/parts/assembly/GTWN7450D0WW .

To purchase the part from GE, go to https://www.geapplianceparts.com/store/parts/spec/WH13X10057 . It is available at other appliance parts suppliers. The price is similar at the vendors that I consider using.

I hope this helps.

Cindy Wells

Nov 29, 2014 | GE GTWN7450DWW 28" 4.6 cu. ft. Capacity...

1 Answer

Washer is filling too much and water is coming out overflow


you need to clean the pressure swith hose on the lft side of tub small rubber hose stop use in liqid soap

Jan 30, 2010 | GE Washing Machines

1 Answer

Gcxrpo9odoww GE washer .. On fill up, it over flows onto floor?


Fill switch could be bad, or fill tube could be plugged making water not stop and it keeps filling. The fill tube goes from fill load selector switch to bottom of tub. Remove from top and blow it out. If this doesnt work replace water load size selector switch.

Jan 17, 2010 | GE WBSR3140DW Top Load Washer

2 Answers

Water runs but doesn't fill tub and wont spin if put on spin cycl


The water-level switch regulates your washer's fill volume. This switch is usually a diaphragm device with a small, clear tube attached between the switch and the bottom of the washer's outer tub. As the water level in the tub increases, the pressure on the air in the tube increases. When the pressure reaches a certain level, it activates the switch, shuts off the water, and signals the timer to begin the agitate cycle. If the switch is defective, it may prematurely signal the water to shut off. If so, you probably need to replace the water-level switch.

Jan 09, 2010 | GE WBSE2090A Top Load Washer

1 Answer

My washer will not start. I press the start/pause button and it just beeps twice and does not lock door or start wash. ge adora model wcvh6260


clean the drain filter located behind the front lower panell, its prob. holding excess h2o and wont let the water fill cycle activate. this happened to mine.

Aug 11, 2009 | GE Energy Star WCVH6260F Front Load Washer

1 Answer

GE WHRE5260E1WW Washer


The mixing valve needs to be replaced. It should be under $50 and is easy to do.

Jan 23, 2008 | GE WHRE5260E Top Load Washer

1 Answer

Too Much H2o


either your waterlevel switch is bad or the hose from the tub to the switch is leaking air. more info would help..ie do you have to turn the water off at the wall for the water to stop rising or do you just have to push the timer knob in?? let me know, i can definitely help to diagnose!!

Apr 24, 2007 | GE WSM2700W Unitized Spacemaker Washer and...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

3,015 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

geapptech

Level 2 Expert

157 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...