The ph has turned off in the middle of using it how can I turn back on? No buttons seem to b working at all.

To activate the shuffle feature:
1. Go into the Settings > Play Mode > Rand Folder.
2. Go back to the menu.
3. Turn off your player, (with the slider on the side, not the middle button.)
4. Turn it back on, and hold down the middle button. The screen will turn off.
5. Hold the middle button down again, and shuffle should work.

What happens when you push the button to turn on the pump?
Is there power to the pump? Did you check the circuit breaker to make sure it is on?

Rod Kidman

US Parts Center

We locate the "seemingly" impossible...

Ph: 888-521-6183

Fax: 801-417-8027

"Chat Live"

NVRAM Initialization:
1. Turn the printer off.
2. Press and hold down CANCEL (X) and Start Copy (button just below the X button) buttons at the same time while powering on printer. *Keep these buttons press while you power on the printer*
3. Continue to hold down buttons until the printer display reads PERMANENT STORAGE INIT.
4. Release the buttons when "PERMANENT STORAGE INIT" is displayed. Printer will return to Ready automatically.

well actually if the ph does not have any other button to turn it off u can not do that, so probably u will need to purchase a new ph

Plasma tvs do not have "back lights" LCDs do. you probably have a bad driver board along with the upper or lower buffer board or maybe both, best to have a tv shop look at it.

Hi,

Locally (in your network) to gather these information, you can enter http ://192.168.0.1/ to get the Actiontec’s web interface and gather the DNS info.

Alternately, for Globelines (Philippines) DNS Servers, you can try:

• 202.52.163.6
• 202.52.163.7
• 202.52.162.39 (ns1.globeidc.com.ph)
• 202.52.162.40 (ns1.globeidc.com.ph)
• 202.52.167.70
• 202.52.167.71

Depending on the time of the day, below DNS varies in performance/speed:

• 203.127.225.10 (g-net.globe.com.ph)
• 203.127.225.11 (g-net1.globe.com.ph)

In some instances, the following also work:

• 202.95.226.66
• 202.95.226.77

The below DNS could also be used but would seem to be reserved for somebody way up the company:

• 203.177.3.100 (theboss.globenet.com.ph)

Hope that this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Ensure there is no jam in the fusing unit. Turn copier off. Turn the copier back on while pressing down on the 2 and 5 keys. Select 1, the software switch settings. Using the arrows on the touchscreen, select dipswitch 3-1. Touch the off key. Press return, then turn the copier off and back on. If the code returns, you may have to replace the temperature sensors in the fusing unit.

could be a number of causes, most common someone fiddling with settings, secondly adsl internet und unfiltered lines so put filter on fax and any ext. ph. lines also contact your telecomunnications co. (and waste hours of time, be put on hold 25 times, told your account number isnt valid, theyre having a glitch in the system, its not their problem, youll have to ring back later, confirm your adress, D.O.B.- Ph no. -credit card no.- tax file no.- and your third cousins 2nd wifes stepsons- ex girlfriends- brothers 4th grade teachers middle name) and ask to have the line checked

Try opening the frothing valve by turning the dial and force water through it instead of steam by pressing the middle, coffee button. You may be experiencing vapor lock. Once the water comes through the steamer valve, turn the steamer knob off and release the coffee button. Then try the steamer button with the steamer dial open. This may do the trick.

IF IT JUST DOESN'T WORK... (But the laser pointer is still working when in 'presentation' mode) You need to 'Sync' the presenter and the reciever... as follows: Turn the presenter on, and turn it over so you're looking at the back of it. See the button in the middle? Press that button, and the button on the USB reciever stick, simultaneously, while holding the two of them quite close together. Problem should be solved. If you turn it on and the display isn't working, or if the laser pointer doesn't work when in 'presentation' mode, you need to change the batteries. I thought I had a dud unit until I found out about the 'Sync' function!!! Definitely on the 'need to add to documentation' list!