Question about Life Fitness 9500HR Next Generation Remanufactured Treadmill

Open Question

MOTOR CONTROLLER COMM ERROR BAD ERROR9 ON LED3

AFTER REPLACING THE WHITE CHIP ON THE BOARD AND PUT THE BOARD BACK IN PLACE I GOT AN ERROR 9 MESSAGE ON THE LED 3 ON THE BOARD. WHAT SHOULD I DO NEXT?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 83 Answers

SOURCE: error message notify maintennce motor

Every time I have gotten this message, I have had to replace the motor controller.

Posted on Mar 24, 2010

Ad

adamandwendy

  • 1 Answer

SOURCE: notify maintenance motor controller comm

I own a gym and have 5 9500's...unfortunately it sounds like it the motor controller board which is around $800. National gym supply or sprotsmith has the part.

Posted on Mar 01, 2011

mbartell

  • 3 Answers

SOURCE: On display stands: MOTOR COMM BAD

Try Carolina Technical Services in South Carolina for all you East Coast guys. They charge flat rate of $175.00 and have a 90-day warranty. Also great turnaround time. Carolinatechnicalservice.com. 864-504-7303. Sure beats sending to California and having to wait for 3 weeks.

Posted on Jul 04, 2011

mbartell

  • 3 Answers

SOURCE: indicates motor controler comm bad

Check out www.carolinatechnicalservices.com. They can help if your boards look like either of the 2 on the website.

Posted on Jul 12, 2011

ercupa190

ernesto cuadra

  • 12223 Answers

SOURCE: The screen says "motor control comm bad", what

Dear Sir: Hello, i will help you, but unfortunately the factory use this software:
System usage statistics on main motor:
By that reason the problem is the Main Motor is faulty!, some technician from the factory must be set up your machine. You must call them for to replace the main motor, and adjusting in the main controller(Boar for control the main motor).
When you had been repair the motor , I will STRONG recommend you to install some stabilizer voltage in the power cord in the receptable is Not expensive, will be costo about us$15.00 aprox.
Thank you in advance, if you need some additional assistance, you can contact me, blessing, sincerely.
E. CUADRA MANAGUA, NICARAGUA. C.A.

Posted on Sep 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHITE DOTS


it is the dpl chip. if you are in the uk you cannot get one only the USA have them, looks like this.0ed54a61-ef76-42d7-a95a-e951b5ac679f.jpg they are not cheap and when putting new on in there is a lot of re-aligning to be done to get the picture back in place. soon the screen will look like a star trek screen saver. to change the chip when the back is off. there is 3 plastic white bits on the board take the caps off and you will find the 3 screws in them.. then when out you need to remove the casing around the chip off heat shield and all. now for the fiddly bit, you need to prize the chip off the board without damaging the board or the part the chip fits in. now I used a plastic splitter 2 and put them iver side and at same time pushed them under and it popped off. no damaged done. just pushed the new on on making sure not to push on the lcd screen in the chip. and them put the board back together. and be fore screwing it back to the plate on the bulb housing. give the chip lcd screen a wipe with a very soft cloth. not screw it down. put every thing back on to the board. now down the back were the bulb housing is there is a switch. get an elastic band and make the switch stick up or down that is up to you just make sure you do this not the 3 screws part is coming up so you need a test card signal you can download them on the internet hook up a pc laptop etc any thing with a screen test picture on it. and turn on tv with out the back on the switch you just did with the elastic band will let the tv turn on. now the screen will be out of place. get to the source you have selected to use laptop etc. and put the screen test picture up. now you need to to keep moving the board with the 3 screws until the screen fits the screw it down and put the caps back on. found it was best to use the HDMI sauce to set up. hope this help you and good look.

Oct 01, 2013 | Samsung HL56A650 56 in. TV

Tip

TV led back-light repair


Tv using power supply unit EAY62810301.

No back-light/sound ok.

No dc voltage measured at P801 led plug.
New board did not fix.
Remove display panel.
With face up, panel will hinge up. (after removing all trim parts) Place folded towels beneath, to prevent strain on tcon ribbon.
Fold other screens up and over on top of display to keep them in right order. Including white background reflector.
Check each series led string with 2*9V batteries and series resistor, minding marked polarity.
Circuit consists of 3 strips of 7 leds all in series.
One bad led disables all .
Check each led of bad string. I used 18V and 1K ohm.
Replace strip or jumper (short) bad led. I just jumpered the bad one that was on edge of panel. (first in string).


http://i.fixya.net25611904-d2havjugub54lsdvnfsaynwf-2-0.jpg

25611904-d2havjugub54lsdvnfsaynwf-2-0_0.jpg

on Mar 28, 2015 | LG 32LN530B 32" 720p LED-LCD TV - 16:9 -...

2 Answers

If a warning light indicates the CPU is not functioning, does that mean I have to get a new processor?


Yes! judging by all the cascade break downs, I would suggest replacing the motherboard, HP has a history with motherboard issues.

Mar 29, 2012 | HP Computers & Internet

1 Answer

The yellow lamp is flashing and printer dosn't work .My printer is pixma mp510 canon


How many times does it blink... 2, 3, 12....

2 times Carriage error [5100] An error occurred in the carriage encoder signal. - Carriage unit (QM2-3753)
- Timing **** film (QC1-9542)
- Logic board (QM2-3827)
- Carriage motor (QM2-3872)
3 times Line feed error [6000] An error occurred in the LF encoder signal. - Timing sensor unit (QM2-3878)
- Timing **** disk film (QC1-9597)
- Feed roller (QL2-1407)
- Logic board (QM2-3827)
- Paper feed motor (QM2-3873)
4 times Purge cam
sensor error
[5C00] An error occurred in the purge unit. - Purge unit (QM2-3754)
- Logic board (QM2-3827)
5 times ASF (cam)
sensor error
[5700] This error takes place when feeding paper from the
ASF after an error occurred in the ASF cam sensor.
- Sheet feed unit (QM2-3762)
- ASF_PE sensor board (QM2-3877)
- Logic board (QM2-3827)
6 times Internal
temperature
error
[5400] The internal temperature is not proper. - Logic board (QM2-3827)
- Carriage unit (QM2-3753)
7 times Ink absorber
full
[5B00,
5B10,
5B01,
5B11]
The ink absorber is full.
Error codes:
Overseas:
5B00: Main ink absorber
5B10: Borderless-print ink absorber
Japan:
5B01: Main ink absorber
- Ink absorber kit (QY5-0178)
1-5
Note: Before replacement of the logic board ***'y, check the ink absorber counter value (by service test print or EEPROM information
print). If the counter value is 7% or more, also replace the ink absorber kit (QY5-0178) when replacing the logic board ***'y, or
register the current ink absorber counter value to the replaced new logic board instead. [See 3-3. Adjustment / Settings, (9)
Service mode, for details.]
2-3. Other Error Messages
5B11: Borderless-print ink absorber
8 times Print head
temperature
rise error
[5200] The print head temperature exceeded the specified
value.
- Print head (QY6-0070)
- Logic board (QM2-3827)
9 times EEPROM
error
[6800] A problem occurred in writing to the EEPROM. - Logic board (QM2-3827)
10 times VH monitor
error
[B200] The internal temperature exceeded the specified
value.
- Print head (QY6-0070)
- Carriage unit (QM2-3753)
- Logic board (QM2-3827)
12 times PG position
error
[5C10] An error occurred in the PG motor during purging
operation.
- Sheet feed unit (QM2-3762)
- Logic board (QM2-3827)
- Purge unit (QM2-3754)
15 times USB Host
VBUS
overcurrent
[9000] The USB Host VBUS is overloaded. - Logic board (QM2-3827)
19 times Ink tank
position sensor
error
[6502] None of the ink tank position is detected. - Spur base unit (QM2-3750)
- Logic board (QM2-3827)
20 times Other
hardware error
[6500] The PCI bus error is detected by the ASIC. - Logic board (QM2-3827)
22 times Scanner home
position error
[5010] The scanner unit cannot detect the home position, or
the scanner unit warming-up is not performed
properly at power-on.
On the LCD, "Scanner is not operating correctly." is
displayed.
- Scanner unit (QM2-3775)
Alarm and Power
LEDs lit
ROM error,
RAM error
A flash ROM or RAM checksum error occurred at
hard-power-on.
- Logic board (QM2-3827)

Jan 12, 2010 | Canon PIXMA MP510 All-In-One InkJet...

1 Answer

CASE WIRES TO PANEL1 CONNECTIONS


The hdd red wire gooes to pin #1 the hdd white wire goes to pin #3 the power sw orange wire goes to pin #6 the power sw white wire goes to pin #8 The reset sw blue wire goes to pin #7 the reset sw white wire goes to pin #5 the power led green wire goes to pin #2 the power led white wire goes to pin #4.
Now the layout of the pins is the long row (5) pins are the odd number pins 9 being the odd one and 1 is the other end of the row. 2 through 8 start at the pin accross from 1 : : : : . I hope this helps you.

Aug 22, 2009 | PC Chips MB PCCHIPS SiS746FX M848A V5.0...

1 Answer

Xerox 6180 MFP's cyan cartridge isn't recognized


There are a number of possible causes of this.

1. Faulty chip on the cartridge, or badly fitted chip.
It will look obviously 'odd' if the chip is incorrectly fitted to such an extent that contact cannot be made between the cartridge chip and the printer. If it looks OK, and you still have the old cartridge, try swapping the chip (complete in its 'carrier') from the new one onto it. If the stays, it's the chip. Confirm this by putting the OLD chip back on the OLD cartridge, and you should get a different message telling you the catridge is empty.

2 Broken cartridge (I've seen quite a few like this - see pictures - the broken one had probably been dropped).

.9025d05.gif
First picture - undamaged cartridge, note 'lug'.


7ef0bba.gif
Second picture - missing 'lug' (cartridge has probably ben dropped)


There is an opto sensor that checks the presence of the cartridge by 'looking for' this lug. The matching one at the other end of the cartridge has no effect.
It is possible to glue a broken lug back onto the cartridge, if the lug is missing, make something that matches the overall size and profile and glue that on - make sure the glue has set/hardened fully before putting the cartridge into the printer.

3 Faulty circuit board, or sensor in printer.

If you've tried the instructions under 1, and the error message stays the same through all the combinations of OLD chip, OLD cartridge, NEW chip, NEW cartridge, AND 2 is not applicable, this is where you are. It could be the opto sensor that 'looks' for the cartridge - you could 'short' this out (be careful to do this on the correct side of the device). Otherwise its a circuit board problem.

Mar 02, 2009 | Xerox 6180MFP/D Printer

1 Answer

Hplaserjet 4100 shows the error 55.0 printer error


Welcome to Fixya !

That is an iternal communications error. The first thing is to shut the printer and turn back on. If the error is still present the first item would be the firmware chip. I would remove the firmware and memory chips and reseat. Make sure you put the firmware chip back in the same slot. If that does not work, contact hp as they have a service not for firmware chip issues (not necessarily yours) and will replace it free. If not the chip it is either the formatter or the engine control board.
The Chips can be found by sliding the rear plastic panel on the right side of the printer towards the back of the printer You are looking at the formatter cage. Open the metal panel and chips are here

Feb 07, 2009 | HP 4100N: HP 4100 laserjet printer , 32MB...

2 Answers

Front panel connections


Hi sjcrofts,
The most common problem for most people is knowing what wire color is positive & which wire color is negative. The colors blue, red, green, light blue, light red & light green are normally positive. The color white & black are negative. Your board uses only 2-pin connectors. The 3-pin power connector can be turned into a 2-pin connector to work with the M848ALU pins.
(Page 13, PANEL1). How to? Take the three pin connector, on the back side of the connector you'll see a small tab that holds the wire into the connector. Use a needle & pull tab up while pulling the wire out at the same time. The wire should slide out. Insert the wire back into the connector next to the other wire. You do not need to hook up the SUS led which stands for suspend.

dff74fa.jpg

Pin 1 is positive & the manual shows this by adding the _P = positive.
Pin 3 which is to the right of pin 1, is negative for the hard drive led. Pins 9 & 10 are not used.

Good luck sjcrofts!
Mike

Nov 30, 2008 | PC Chips M848ALU Motherboard

1 Answer

Front load washer won't start


Telescope, Im assuming your model starts with 417.44092, Kenmore made by Frigidaire. You have the best model with the digital display. Try unplugging the machine for 5 minutes to see if you can reset the board. If that doesn't work put it into a test mode by doing the following: Turn the dial to drain spin, press cancel to turn off the led's. Within 5 seconds press and hold the options and pause/cancel together for 5 seconds. All the led's should light. Now by turning the dial 1 click at a time clockwise you are going to test the following. 1rst click- hot water solenoid 2. bleach solenoid 3. Bleach and wash water solenoid 4. door lock solenoid activates 5. door lock solenoid de-activates. 6. the washer will fill and tumbe. 7. washer will fill and spin 8. drain pump and door lock will activate and washer will go in high spin. 9 clicks from the start, the last error code will be displayed. To clear the error, press and hold the options and cancel buttons for 3 seconds. To exit the test, just unplug the washer for 5 seconds. Sometimes these electronic boards just get a glitch and have to be reset. Make sure that the dispensor door is shut all the way. Try these things first...Catriver..post back.

Nov 04, 2006 | Kenmore Energy Star 44092 Front Load...

Not finding what you are looking for?
Life Fitness 9500HR Next Generation Remanufactured Treadmill Logo

Related Topics:

201 people viewed this question

Ask a Question

Usually answered in minutes!

Top Life Fitness Exercise & Fitness Experts

Vincent G
Vincent G

Level 3 Expert

2361 Answers

Android Man
Android Man

Level 2 Expert

278 Answers

Kenneth Simmons

Level 3 Expert

1027 Answers

Are you a Life Fitness Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...