Question about Maytag Neptune MDE5500AY Electric Dryer

1 Answer

My dryers control push pad is not working - Maytag Neptune MDE5500AY Electric Dryer

Posted by on

  • Mike Kunkel Apr 14, 2016

    If it's not responding to any buttons, check the 3300uf @ 16V filter capacitor on the control board behind the touch panel. Simple fix usually. The capacitor is definitely bad if the top is swelled and/or leaking.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 90 Answers

Type Maytag Neptune push pad into YouTube and see if the video comes up, thanks!

Posted on Dec 03, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

LG Dryer Power button is pushed in


More than likely, the button pad support inside the panel is broken and the whole control panel will need to be replaced. You will need the complete model number to get the correct part number.

Nov 06, 2011 | LG DLE7177 Dryer

1 Answer

Problem with my maytag neptune mde7550 dryer will not go through any cycles by useing touch screen and will not switch off by touch screen


The only way possible to see if the touch pads are working is to test the voltage of the control pads when it contacts. The input of the Microprocessor should be checked for the pad control impulse to come in. If there is no trigger voltage to the mP this can be the control pad problem.
The mP must be checked for the working voltage and also the frequency oscillation at the crystal leads. If so the mP is working with a suspected control pads which are not able to set the program or timing.
There is no way but to remove the sticker pad and replace, One difficult way to have a chance is to remove the carbon sticker pads and check continuity , You can use a carbon pen to line the tracks so that the multi-meter reads a continuity. With this you can have a temporary fix

Oct 17, 2011 | Maytag Neptune MDE5500AY Electric Dryer

1 Answer

I have a Whirlpool gas dryer model no. GGW9868KQ3. My problem is when you press any touchpads on the control panel nothing lights on. There is power going in to the control board. Do you think it's a...


The only way possible to see if the touch pads are working is to test the voltage of the control pads when it contacts. The input of the Microprocessor should be checked for the pad control impulse to come in. If there is no trigger voltage to the mP this can be the control pad problem.
The mP must be checked for the working voltage and also the frequency oscillation at the crystal leads. If so the mP is working with a suspected control pads which are not able to set the program or timing.
There is no way but to remove the sticker pad and replace, One difficult way to have a chance is to remove the carbon sticker pads and check continuity , You can use a carbon pen to line the tracks so that the multi-meter reads a continuity. With this you can have a temporary fix.

Thank you for using Fixya

Aug 24, 2011 | Whirlpool GGW9868K Gas Dryer

2 Answers

Says "Controls locked"


Press and hold the END OF CYCLE button for about ten seconds.

Nov 28, 2010 | Whirlpool Duet 7.0 Cu. Ft. Super Capacity...

2 Answers

Control panel lights are on, but when you push the on button, nothing happens.


Hi,

There can be many reasons why your dryer will not start or turn...

The most common causes are the belt breaking or jumping off, or the motor goingbad...

Here are a couple of tips that I wrote will help you to figure out why yourdryer will not run...

Dryer Repair - The Dryer is not Turning

Dryer Repair - The dryer will not start


heatman101

Sep 30, 2010 | Maytag Neptune MDE5500AY Electric Dryer

1 Answer

Start/pause button not working, is it the control panel or the control electronics board?


First unplug the Dryer and allow about 5 mins to pass, this will allow the board time to reset, plug Dryer back in, if problem is still present, its possible that the touch pad is defective on the dryer, if other functions work when touched, it is the touch pad, and not the Board

May 29, 2010 | Maytag Neptune MDE5500AY Electric Dryer

1 Answer

Control wont work stuck on low heat & delicates


Sounds like the control board has gone out on you. Also, you can check for any thermal fuses that my have gone out as well. You will need to refer to you wiring diagram for your specific dryer brand and model.

Apr 10, 2009 | Dryers

1 Answer

Marathon Compucare Dryer


Could be a touchpad problem

Dec 09, 2017 | Dryers

1 Answer

Whirlpool dryer calypso touch pad stopped working


CHECK YOUR INSRUCTION MANUAL TO SEE IF THERE IS A CHILD LOCKOUT FEATURE ON THE CONTROL PANEL. USUALLY, THERE IS A TOUCH PAD TO HOLD FOR 5 SECONDS TO LOCK/UNLOCK THE CONTROLS. YOU CAN ALSO TRY UNPLUGGIN THE DRYER FOR 5 MINUTES TO SEE IF THE MICRCOMPUTER WILL RESET.

Apr 21, 2008 | Whirlpool GEW9250 Electric Dryer

Not finding what you are looking for?
Maytag Neptune MDE5500AY Electric Dryer Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Dryers Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Brad Brown

Level 3 Expert

18157 Answers

Are you a Maytag Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...