Question about Craftsman 42 in. Deck 19.5hp Lawn Tractor

1 Answer

Torgue for head boolt - Craftsman 42 in. Deck 19.5hp Lawn Tractor

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    Visited the website for 30 consecutive days.

  • Craftsman Master
  • 1,669 Answers

PartsTreeRepairClinic will help

Posted on Feb 07, 2018


1 Suggested Answer



Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Torgue settings for cyl head ,mais and big ends on 1985 kb2200 isuzu

don t know the torgue for that model but i was told by old timer to spend the money on new bolts. used bolts have been stressed and you take a chance on snapping off after getting hot

Oct 29, 2017 | Isuzu Cars & Trucks

2 Answers

Head bolt torque engine CA20 nissan

Head bolts Nissan skyline ca20

Sep 02, 2013 | Cars & Trucks

1 Answer

Water leaking from engine head bolt, what would cause that to happen?

Some engines had head bolts that went thru water jackets, remove and put sealer on it then torgue back down. Does it overheat? If that doesn't fix needs head gasket.

Dec 15, 2010 | 1997 Pontiac Sunfire

1 Answer

I would like to know the location of the Idle Control Valve for the 1996 Saturn SL1

there are to eletrical components next to one another. The throttle position sensor and the idle control vavle. They are right where the air supply housing goes into the metal part of the air intake system. Right at the firewall the air intake line, a big rubber hose, attaches to the metal trhottle body. The bottom of the two is the idle control valve. It has an oblong electrical connection and uses a small "torgues" type male wrench to get the two screws out. Torgues is the star shaped screw, rather than a hex head of phillips head type screw.

Jul 27, 2010 | 2001 Saturn S-Series

1 Answer

Torque settings on head

Can I get a “very helpful” rating on this answer?

Aug 12, 2009 | 1992 Suzuki GSF 250 Bandit

1 Answer

Torgue specs for head bolts

I would call autozone, in there computer when you ask to purchase a head gasket, they can tell you the order and torque for the head bolts. That is the quickest method to advise. I hope this helps

Aug 08, 2009 | 1999 Volvo S80

1 Answer

Head bolts

I'm assuming you meant a 1.8L 4V, if so the torgue settings for the head bolts are
stage 1: 30 ft-lbs
stage 2: 44 ft-lbs
stage 3: Angle-tighten a further 90-degrees
stage 4: Angle-tighten a further 90-degrees

Also I recommend you buy new cylinder head bolts from the vdub dealer, they say you don't have to with a gas engine but only with diesel engines you should, from my past experience it felt like the old bolts were going to snap off to be safe buy new ones. If you have never done this before "stage1" this means each bolt gets this one time, then after you have done each bolt at this torgue then you do the bolts again (stage 2) with this torgue ect. Remmeber to always cris cross your bolting and work from one side to the other the same time for each stage. Vdubs 4-ever !

Mar 23, 2009 | 1997 Volkswagen Golf

Not finding what you are looking for?
Craftsman 42 in. Deck 19.5hp Lawn Tractor Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Craftsman Garden Experts

john h

Level 3 Expert

22486 Answers


Level 2 Expert

158 Answers


Level 3 Expert

85223 Answers

Are you a Craftsman Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides