My display day and time are incorrect

8AM-4PM
SARS, Monday hours
Heritage Day (Observed) might affect these hours

I don't have the manual can do send me the instruccion for programing or send me the link in you tube Tks

Sounds like the same problem I have been having with my 2002 Sedona for
the past 6 or 8 months. It would run OK for several days, weeks, or months,
then just quit. If I let it set for 10 to 20 minutes, it would restart and run fine
for at least the rest of that day. About 2 weeks ago, I was fortunate that it happened when someone was with me, so I was able to determine that it
was not getting any spark. Since then the problem has gotten worse and
more frequent - it was happening almost every day and would take over
1/2 an hour before it would start again. This morning was the last straw.
I drove for about 4 miles and it quit. Took 1 hour and 10 minutes before it
would restart. Drove another 2 miles and did it again. This time it took
1 hour 35 minutes before restart. After 1 more mile, it quit again. Took 2
hours, this time. Made it another mile and BAM! - did it again.
My bro towed me home. I determined that it is most likely NOT the crankshaft position sensor, because 99% of the time they either work,
or they don't. Very rarely does it cause in intermittant problem. The most
likely suspect is the engine computer. That was always a likely culpret
when I worked on GM cars. Today I installed a $50 junk yard engine control computer. I am crossing my fingers!
I will know on Thursday, as I have a 50 mile trip to make.
I will post again on Thursday, to let you all know.

hi.
some radios will lock out permanently after a certain number of incorrect codes.
most will have a time lock on them so after so many incorrect tries, you have to wait a certin time before you can input any more codes. this can be anywhere from 30 mins up to 24 hours depending on the radio.
wait for a few hours before trying any more codes.

if you can give the make and model of the radio, i may be able to find out more information on the lockout

You have to run the clock back. Press Time/Date and then press up or down after you run it 24 hours the date will change, and the date will move day to day.

Here are already prepared template time sheets of which your description fits several.

http://office.microsoft.com/en-gb/templates/CT101172771033.aspx?av=ZXL000

Hey here is something you can use to adjust the time on your T7206.To Change the Time:
1. Press the CHANGE softkey Display will read: "Hour:
2. Press the CHANGE softkey Display will read: "Hour: _ "
3. Enter the new HOUR. (in 24-hour format - Ex.: 5:00pm = 17:00. Display will then read the new Hour programmed.
4. Press NEXT Display will read: "Minutes: # # "
5. Press the CHANGE softkey Display will read: "Minutes": _ "
6. Enter the new MINUTES.
To Change the Date:
1. Press NEXT Display will read: "Date DD MM YY"
2. Press the CHANGE softkey Display will read: "Year: # # "
3. Press the CHANGE softkey, (If the year is incorrect) Display will read: "Year: _ "
4. Enter the new YEAR Display will then read the new Year programmed.
5. Press NEXT Display will read: "Month: # # "
6. Press the CHANGE softkey, (If the month is incorrect) Display will read: "Month: _ "
7. Enter the new MONTH Display will then read the new Month programmed
8. Press NEXT Display will read: "Month: # # "
9. Press the CHANGE softkey, (If the day is incorrect) Display will read: "Day: _ "
10. Enter the new DAY Display will then read the new Day programmed

Let me know how that turns out and good luck

quickly press the bottom-left button twice.
then, press the bottom-right button once, and then the top-right button once. this should add 1 to the day. keep pressing the top-right button until u get the right day, the press the top-right button again.

now, how do u change the time format back to twelve hr. ?