Enter diagnostic mode in mod 11028002010 toploader he washer

With the washer off, press any button other than the Power, Start, Stop and hold it for 3 seconds then release it for 3 seconds, hold it again for 3 seconds then release it for 3 seconds and finally hold it again for 3 seconds. All the lights should come on an 88 is in the display. When the 88 goes away be ready to read the code that comes up. An automatic test will then start that has 9 steps. You can advance through by pressing the same button used to enter diagnostics. If a code is there it'll be displayed.

bad control board

DIAGNOSTIC MODE
To enter diagnostic mode follow the steps below.
1. Turn the power on at the power point but off at the machine.
2. Press and hold WASH TEMPERATURE SETTING DOWN and then press POWER until the
machine gives 2 short beeps and lights up.
3. Release the buttons after the beeps as the beeps indicate diagnostic mode has been entered.
4.1 Last Fault Data
When in diagnostic mode the last fault can be found by pressing the SPIN SPEED UP or DOWN
buttons until the HOLD and SLOW lights are illuminated. Binary can then be read from the wash
progress lights.
4.2 Drain Pump Test
MW Washer
When in diagnostic mode press SMART TOUCH CYCLES to activate the drain pump. To
deactivate the pump, press SMART TOUCH CYCLES again.
GW Washer
When in diagnostic mode press REGULAR to activate the drain pump. To deactivate the pump,
press REGULAR again.

4.3 Water Valve Test
The water valves can be activated in diagnostic mode by pushing WASH TEMPERATURE SETTING UP to activate the Hot Valve and WASH TEMPERATURE SETTING DOWN to activate
the Cold valve as with previous models.
Pressing each button once will activate the valve. To de-activate valve press the same button
again. This is also good to use when installing machines as it takes the shock out of the fittings
and seals and allows checking for leaks on the inlet hoses, both machine end and tap or super-tub
end.
Caution: Do not leave the machine unattended when either or both valves are operating

Is there a number after the F code?

Thats ok heres what the code means: Whirlpool Cabrio Washer Fault Codes.

Means primary control failure and to resolve this you'll have to replace the machine control assembly. This error should be fixed by whirlpool as its a common issue with whirlpool Cabrio washers, you can call 1-800-253-1301 whirlpool will send a tech. to fix it and pay for the part.

Hope helps.

I think your washer is similar to the one listed here under "Whirlpool apt size newest washer," (right after the list of topics). The sequence for entering diagnostic mode is on the page listed as "two."
http://www.applianceaid.com/beltwasher.html

PUBLIC LIBRARY--WIRING DIAGRAM RECONNECTED ALL OK

It appears your timer has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

look for tech sheet. this will tell you how to enter machine into service mode. Its located either behind bottom kick panel. or under top panel.

check you lid switch

There is a connector under the steering column, you need to buy an OBD 2 system scanner to plug into that connector and access the codes. The system is always in diagnostic mode, OBD 2 stands for On Board Diagnostics second generation.