Error code 141. How can I fix it?

To solve the E2 error on your Scanfrost washing machine, you can try the following steps:

1. Check the water supply: Ensure that the water supply is properly connected and turned on. Make sure there is sufficient water pressure for the machine to operate.

2. Clean the filter: Locate the filter on your washing machine and remove any debris or lint that may have accumulated. A clogged filter can cause the E2 error.

3. Check the drain hose: Ensure that the drain hose is not clogged or kinked. Straighten any kinks and remove any blockages if necessary.

4. Check the drain pump: The E2 error can also be caused by a malfunctioning drain pump. Inspect the pump for any blockages or damage. If needed, clean or replace the pump.

5. Reset the machine: Turn off the washing machine and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on again. This can sometimes reset the error code.

6. Contact customer support: If none of the above steps work, it's best to reach out to Scanfrost customer support for further assistance. They may be able to provide specific troubleshooting steps or arrange for repairs if needed.

Remember to consult your washing machine's user manual for any specific instructions or warnings before attempting any troubleshooting steps.

Several possible fixes:

http://www.fixya.com/support/t1225051-kenmore_elite_he5_error_code_f30

Quoting:
"F 30 code can be reset by un plugging power cord for 5 minutes also pull out the detergent dispenser and reach all the way in to the back there is a small plastic flapper valve move it from side to side with your finger this will rest code f30 and save a tech visit.."
-----------------------------------------
https://removeandreplace.com/2016/01/18/kenmore-elite-dryer-error-fault-codes/

Kenmore Elite Dryer Error Code = F30 Error Condition = Restricted Outlet Airflow
Check or Repair Needed = Check the lint screen filter and clean of any lint. Remove fabric softener buildup on the lint screen if necessary. Clear lint blockage restriction from the air vent exhaust system.

------------------------------------------------------
https://www.shopyourway.com/questions/1125417

Lint cleaning
------------------------------------------------------

http://www.fixya.com/support/t25862220-error_code_f30


What is error code F30?
Kenmore elite oasis st dryer - has power but won't run. Thermal fuse is NOT where I expected from videos I have watched.

Posted by Tom berwick on Sep 13, 2015

• Talk to a Repairman
• Comment
• Flag
• More

2 Answers

The F30 code is a false code. It does not mean anything. The dryer will work fine. When I worked for Whirlpool, this was a programming issue. I owned the same dryer. It displayed this code and engineers explained this to me. The dryer worked fine.

Unplug it overnight. That will definitely reset it. Did you remove the cover where e the lint filter goes in. It is usually held in by two screws from the inside. There should be two wires leading to two metal strip on that cover. Make sure they are clean. You can also reach down into the lint trap to remove any more lint.

Check the following link: http://www.laundrynation.com/manuals/wp-content/uploads/2011/05/wascomat_dryer_selecta_control_programming_manual.pdf
On page 13 it identifies the E 08 error as overheating air (inlet or outlet). Chances are, it is the outlet that has gotten gunked up from lint or other material. Pull the vent tube off, vacuum out lint traps, clean the outlet tube, reset the machine. If the dryer is linked with other dryers on a multiple-link vent system, cleaning the vent lines may be necessary to avoid the problem.

most likely a faulty heat element or thermal link on the heat element canister. check with ohm meter. replace.

Error code E60 Fix... Press the reset button in for 5 seconds. The computer board needs resetting. You can also try to reset it by switching the machine off and unplugging it to allow any residual charge to clear from the memory chip. The next step is to clean out the filter at the front - remember to empty the water out first. After a couple of hours, switch the machine on, press reset and then spin to empty any remaining water. If the problem still persists then it is due to Fault in washing NTC sensor, wiring or main PCB.

Hi You can Try

Error Code 5100
Solution 1:
Clean the timing strip.

Solution 2:
The purge cap (the white sliding mechanism that the print head parks to when it's not in use) may be not lubricated well enough .
And Also
Lubricate the sliders with some white grease (don't get it on the small wipers or the black caps); this repair probably require to remove the right panel off of the printer to gain access to the purge mechanism.

All The Best: Pineworks

check the drain filter in the bottom left corner behind the access door

Mine has been beeping incessantly as well. Turned out that even though I was cleaning the filter after each load, there was still a ball of lint the size of a tennis ball that was blocking the lint sensor. To fix, I removed the screws from the plastic piece that holds the lint trap and slid it out (it won't come out entirely.) Then I used the mini attachments for my vacuum to remove the lint from the bottom of that space. Once I did that, the dryer has been working flawlessly.