Blurred color images

If the message Change Imaging Unit Magenta displayed refer to imaging unit with contents a developer.The Imaging unit life is 80.000 copies.
The imaging units located after front door when is located the waste toner box.
If the message M toner end/change the M toner displayed refer to toner cartridge
The toner cartridge life 15.000 copies 5% saturation.In full color mode the color saturation is 80% and the color toner life is 6.000-8.000 copies.
I think your problems is a toner not the developer.

It means that the printer is not spraying properly all colors.

If the bar are regular, that means that the printhead is blocking the spry at regular times intervals.

Sometimes this problems is related to the printhead.

You find out if it is a faulty printhead by removing it, leaving in in isopropyl alcohol overnight or replacing it.

If printhead is fine then it is a problem with the control board.

Hi,

You can photocopy on this printer by following these steps:

Note: You can make a quick color or black and white copy.

Press Color Copy or Black Copy on the control panel.

To make black and white, gray, or color copies:
1 Open the top cover of the All-In-One.

2 Place the item you want to copy face down on the glass. Make sure

the upper left corner of the front of the item aligns with the arrow.

3 Close the top cover.

4 Open the Lexmark All-In-One Center (see page 3).

The All-In-One Main Page displays.

5 Click See More Copy Settings to review and change the copy

settings.

6 Select your copy settings.

Note: You may want to reduce or enlarge the image.

7 Click Copy Now.

I hope this works for you. Kindly reply for further assistance. Good Luck!

Thanks for using Fixya!
Mongkey
TIPS: Is your computer slow? This might help
http://www.fixya.com/support/r8158906-diy_manual_pc_tune_up
(for Windows only)

Readjust ur tube back to the original position.Ur convergence is dead,Must know to solders?Replaced the 2 convergence ICS and all it resistors.Tv Repair World.com,Tvrepairkits.com to buy a convergence kit to repair it ur self.The shop will cost u $300 for parts and labors.

Defective main motor
• Image transfer belt out of position
• Belt mark blurred or absent

Right from the service manual
My best guess is belt mark blurred or missing
or image belt out of position

Try reseating the LVDS cable.It runs from the main signal board to the T-con board at the top of the panel.

To create a glow: make a copy of your image you want to glow. paste to the side or original. select original. Convert to Bitmap, then use Gaussian blur, select pixel width of blur, preview it, then apply it when it look good. Put your copied image on top of the blurred image, bringing the copied image TO FRONT. voila NOTE change color of image to be bit-mapped BEFORE you convert to bitmap for a COLORED Glow

This sounds like a registration problem.

Use the menu (on the printer) to print antest page AND a configuration/information page.

Look (critically) at the alignment of the seperate coloure Yellow Magenta Cyan. You will probably find that these are out of aligmnent across the page.

The cause of this, is that the printer can't perform a calibration properly (printer probably takes a long time when calibrating too) and is usually down to failure of one of the sensors on the transfer belt.

Sometimes you can clean these and solve the problem, but often is a failure of the component itself. Thes are NOT available as a spare part, and the repair to correct this would need a replacement transfer belt.

Transfer belt replacement in this printer is quite an involved task, though it is within the capabilities of someone with reasonable mechanical aptitude.

Please describe the allignment problem

The doe problem go away if you bang on the side of the camera? there is a known issue with the CCD sensor on certin model cameras that after a few years the glue or somthing dries up inside the sensor and it developes a bad connection. Canon has admit they know about this problem and they will fix them free of charge and pay shipping both ways. Sometimes users can bang on the side of the camera and the camera will work properly again but not for very long. I cant see your display so im not sure if thats it or not but the problem has this purple blackish symptom. Go to the canon usa webpage and then search around for your camera model and if there is a known issue it will say on their site. Then there are ways to contact them on their site.