What is reset code?

Most auto parts stores provide a complementary service of getting a readout on any OBD II codes. Suggest you check if in your area any stores would provide you this service. The goal of the parts store would be to provide you with the parts necessary for the repair.

It is a quick process where they connect on the drivers side a code reader under the dash and read the codes. They will provide a printout showing the likely source of the errors.

Disconnecting the battery to reset codes is not recommended
.
Hope this helps?

Hi, it looks like a bad controller board. Try resetting it from in service mode with 7807. Also if you can view or printout the error history with 5990-004 for further trouble shooting. Hope this helps

Before you reset it you need to find out what set it. If you don't have a code scanner take it to Autozone, they will do it for free and give you printout of the fault codes.

Could be a bad spark plug or coil pack. Also could be a bad fuel injector. Is you Check Engine light on? If so, you need to have the fault codes read to see what the problem is. Take it to Autozone, they will do it for free and give you a printout of the faults.

Sir, i added new toner and new developer but my printout is dull. What i do?

Either you purchased a a bad quality remanufactured toner cartridge or your fuser film is damaged.

If there is some kind of debris in black color that is on printouts, your fuser film might be damaged. Have a printer technician replace it.

If there is no debris, only bad quality printouts, it's the toner cartridge that needs replacement.

try to change your printer cable and dont forget to check your printer driver if it is default to epson lx300+

paper is either upside down or you have a bad ccd or you have a bad main board

reset the machine... copy and then print

flip paper upside down and copy then print

check fuser if it is cold after print... if it is cold then bad fuser... if it is warm then bad main board or ccd

if you get printouts but no copies bad ccd

if you cann't get copies and no printouts after all these tests then bad printboard or main board


I’m happy to assist further over the phone at https://www.6ya.com/expert/norman_d2fa496dce30c65d

Canon GENERIC "S" SERIES RESET CODE
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the
"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.

Performing a Fault Reset 14 will reset your WorkCentre and will help to clear error codes.

1. Find the pink Clear button on the Control Panel of the WorkCentre.
2. Find the button below the word Auto.
3. Press these buttons in the following sequence: [Clear], [Auto], [Clear], [Auto] NOTE: All of the lights on the Control Panel should go out and the LED Display should go blank. If the lights do not go out, then repeat step 3 until they do. It may be necessary to increase or decrease the pace of the [Clear], [Auto], [Clear], [Auto] sequence.
   
4. Press the [10's] key one time and the [1's] key four times to enter '14' in the LED Display, as if you were to make 14 copies.
5. Press the green [Start] button.
6. Press the pink [Clear] button two times.
7. The WorkCentre should now warm up and come to ready.
8. If the above steps do not clear the error code, repeat steps 3 to 6 a second time.