Frigidaire GLTF2940ES Front Load Washer Logo
j
john mcgurk Posted on Apr 13, 2016
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

How do I fix the washer from stopping early and not spinni g the close out? The washer shuts off before it's done

1 Answer

  • Official Brand Answer 2,267 Answers
  • Posted on Apr 19, 2016
Frigidaire
Official Brand Answer
Level 0:

Joined: Mar 18, 2014
Answers
2267
Questions
0
Helped
1289301
Points
2557

Hey John, thanks for your inquiry!
Based off what you have described your Frigidaire washer is stopping early and not spinning clothes properly. It sounds like this could be an issue within the control panel or a miscommunication within the electronics. I would suggest performing a reset on the washer to help clear out any miscommunication and you can do that by disconnecting the power cord for at least ten minutes. You may need to have a technician out to review your washer if the reset does not help clear out the error. I hope this information helps towards the repair of your washer. -Matt

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Lately when i go to put in a load of clothes in the washing machine there is water sitting in the the drum. Its not there when I take a load out when its done washing so i know its draining and spinni

is it just a small amount in the door rubber if so its just condensation leave the door open slightley to air off if there is loads of water it may be the pump got a blokage or the cylinders that let the water into the washer leaking slightley but there would be a load of water if that was the caes hope this helps ivan
0helpful
1answer

After wash is almost done, it stops and says 09 minutes left and then f

Possible fault in the timer control unit. Please check the washer on different modes particularly on the easy wash mode and see if the fault is occuring. If it is consistant that the timer is running behind then the clock might be out of sync with the processor controller.
Check to see if the motor is free, the capacitor is good because the fault can also occur due to a load shut off. .. spcially if the motor is running slow or the drain pump is faulty shutting an early action.
So check this out.
0helpful
1answer

Washing Machine shuts off by itself during cycle

Not sure what you are saying.. if washer is off balance, it will shut off, check legs are secure to floor and unit is leveled. If washer lid isnt sealed or lid switch is bad it can shut off at spin or start cycle. Depends on unit model. The smell can be a burning belt from a heavy wet comforter or you have mildew from water not properly drained from unit.
0helpful
1answer

Washer stops early cycle. In the first minute or two while it is filling with water it stops. If it gets past that stage it works fine.

gud day,,your washer has a little problem you must only adjust the washer timer,,you can fixed it by your self by opening the time at the back..tnx
0helpful
1answer

Washer keeps filling with water...

you hae a stuck float switch, it shuts water off when it reaches a certain height, fixing it involes removing the top of the washer (not easily done)
0helpful
1answer

WHIRLPOOL ELECTRIC WASHER STOPPED WORKING MIDWASH BC OF OVERLOAD?

My wife did the same thing,trying to do all the laundry at one time.Even if it says high load compasity it will only handle so much.sounds like you killed your motor.Hope this helped.
For more help go to live chat.
lenwest
3helpful
2answers

Water doesnt stop over fills the tub

Most washers have a pressure switch in the control panel that controls the water level. A plastic or rubber tube connects from the bottom of the tub to the pressure switch. The washer will fail to stop filling if the tube comes loose or develops a leak. The other possible problem is that the pressure switch is defective.
0helpful
1answer

No spin zone

Try this: Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too.

Rate me pl.....if helped.
Not finding what you are looking for?

116 views

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...