Question about Numark Music

1 Answer

How do is fix my Numark m6 bleeding cross fader

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Numark Master
  • 3,156 Answers

/it's most likely a defective fader, but before replacing it, get a can of Deoxit5 or fader cleaner and spray inside the fader, then move it the full length os travel about 20 times to see it that clears it up.

Posted on Jul 10, 2016


2 Suggested Answers



Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Spencer Stitt

  • 11 Answers

SOURCE: THIS IS NOT A NUMARK. need help with denon x120

I like the Pioneer DJM-600

Posted on Jul 21, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Fix p+g faders on mackie control

You might call mackie for a suggestion at 800-258-6883. Sometimes there may be older parts in stock at other Mackie distributers around the world. Here's a list of contact info Mackie International Distributors It doesn't hurt to ask and email is free!
I had good luck getting parts for various musical electronics out of Canada

Feb 01, 2015 | Mackie Music

1 Answer

Fader repair looks like my fader is off track its two of them sunk in how can i fix it

By "fader" we'll assume you mean the sliders on a mixing console, etc. These potentiometers are rectangular in shape and are usually held together by bendable "tabs" that hold the mechanical mechanism together. If you have pushed the control apart, you will need to try and realign the casing and bend the tabs back into place, but be warned. They may also be destroyed and need replacing.

May 23, 2014 | Music

1 Answer

Souncraft GB4 ch 16 Right mix chanal dead

If you aren't using one of the group outs you could re-route the main L/R through one of them. I can't remember if that board will let you configure the MONITOR outs for either PRE/POST fader but if so you could go that route too.

Otherwise that fader is most likely dead & you'll probably have to replace the MAIN L/R, master output module if you can't find a competent tech to fix just the fader.

Feb 14, 2013 | Soundcraft GB4 16 Mixing Console

1 Answer

How hard would it be to change a fader control on a peavey escort 2000

Changing faders USUALLY involves removing all panel hardware so that circuit board can be removed to get at the fader. It is often a LOT of work with a boit of hazards along the way.
If the control is noisy I want you to try something before replacing the fader. Get a can of CRC226 available at Home Depot in the Electrical department... about $2.70 for a can. Using the included plastic spout tube, squirt a bit into the center of the control where the knob is. Work it back and forth and then put a little more in and test if it is better or fixed.
NEVER use DeOxit or Blue Shower in faders!!!!! It removes the lube that is required in the fader.

Jan 04, 2011 | Peavey Escort 3000 Packaged PA Speaker...

1 Answer

What lube can i use to clean numark nuvj crossfader. i'm gettin a leak while using the fader.

Usually a "leak" from one side to the other is an indication of a cracked resistance element. The fader would have to be replaced.

I lube the faders on my mixers using CRC226 availablle in the electrical dept at Home Depot. Use sparingly.

Aug 12, 2010 | Numark Nuvj DJ Video Mixer

2 Answers

I think my crossfader stop working for some reason. when im on side B i get sound then i slide over to side A and i still get sound from side be,,, all the assign are right also the bass mid and hi kill...

I suspect one end of the crossfader pot has broken from the element. The fader probably costs less than $5.

You likely will have to remove all the knobs and some screws to seperate the board with the fader from the front panel so you can replace the fader.

VERIFY the pot is bad with an ohmmeter before dis-assembling however.

You MAY be in luck. It looks like the cross fader has a connector which MIGHT allow you to remove it or certainly only a small board for replacement, seeing these take abuse.

It appears that the cross fader is a dual 100K type B taper.

Apr 26, 2010 | Behringer DJx700 5-Channel Pro DJ Mixer...

1 Answer

Crossfader Selectors scratchy

The sliders on MOST of the mixer devices are pretty weak. They are subject to dirt or liquid getting into the slot and spoiling them. Fix is to replace them. You usually can find replacements at Digikey or Mouser that are suitable. The parameters are the resistance, the packaing and the length of throw AND importantly the "taper" of the resistance element.

Sep 08, 2009 | Behringer DJx700 5-Channel Pro DJ Mixer...

Not finding what you are looking for?
Music Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Numark Music Experts

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2015 Answers


Level 3 Expert

3156 Answers

Steve Pack
Steve Pack

Level 3 Expert

4331 Answers

Are you a Numark Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides