Paper jam problem

I'm not sure if you tried this, yet, but try the following link from canonusa.com website regarding clearing paper jams. Click on 'clearing paper jams inside the printer' on the page:

http://www.usa.canon.com/cusa/support/consumer/printers_multifunction/pixma_mp_series/pixma_mp810#ServiceAndSupport

This error message is displayed by the printer when paper is jammed in one or more locations. In such a case, users are recommended to remove the jammed paper from the specified location. The entire paper path must be checked for any pieces of paper. To stop the message, open and close the top most cover of the printer. Lastly, verify the flags and the sensors. If the problem persists, the cause of the error message could be a broken sensor or sensor lever.

Before you can clear a "PAPER JAM" or "PRINTER JAM" error, you must locate where in the unit the paper is jammed.
First, unplug the machine for safety and disconnect the telephone line. Next, follow these instructions based on where the paper jam is located.


Paper is jammed inside the paper tray:

1. Pull the paper tray out of the machine.

1. Pull out the jammed paper to remove it.

1. Reload the paper in the paper tray.
   
   
2. Reinstall the paper tray.
   
   
   

Paper is jammed inside the machine:

1. Remove the jam clear cover on the back of the unit. Pull the jammed paper out of the machine.

1. Re-insert the jam clear cover.
   
   
2. If you can not pull out the jammed paper, lift the scanner cover from the right-hand side of the machine until it locks securely into the open position.
   
   
3. Remove the jammed paper.
   
   
   

   
   
   

4. Check the print head's position. In the example photo the print head is positioned at the left hand side of the platen area.
   
   

   
   
   
   

5. Gently move the print head to the center.
   
   
   

   
   
   Note Be careful to not force the print head to move.
   If the print head is positioned at the far right hand side, you cannot move it. Please contact Brother Customer Service from "Contact Us".
   
   
   
   

6. Examine under the print head. If anything is found, remove it.
   
   

   
   
   Note Use a flashlight if necessary to check thoroughly.
   
   
   
   
   
   

7. Lift the scanner cover to release the lock. Gently push the scanner cover support down and close the scanner cover.
   
   
   
   
   

   
   
   
   

8. Reconnect the power cord and telephone line.

Note To prevent paper jams, do not put multiple kinds of paper in the paper tray at the same time.

If the message continues to appear on the LCD, the machine will require repair. Please contact Brother Customer Service from "Contact Us".



Thanks for using fixya......

Hi,

most likly hood is your exit sensor is faulty. The printer work in this way. if it does not print out all the document. it will print again. that is why you kept getting this same issue after a jam open and close door it will print again.

replace the exit sensor it will help.

Dear
Inside the back panel there are paper sensors attached to lever, a small spring connected to lever to keep its home position, the spring may dislocated from its position or the lever sticked to the base. some times a small piece of paper sticked at this may cause the problem.
Thanks.

HP LaserJet 4, 4m, 4 Plus and 4m Plus Series Printers - False Error Message 13 PAPER JAM ISSUE: After clearing all jammed paper from the HP LaserJet 4, 4m, 4 Plus, or 4m Plus series printer, the display still reads 13 Paper Jam . Even after cycling the power off and then back on, the error remains. SOLUTION: Open the rear door of the printer. There is a paper sensor near the upper right hand corner of the fusing assembly (just below the right edge of the long yellow warning sticker on the fuser) that can cause paper jam error messages even when there is no jammed paper in the printer. Toggle the thin black plastic lever up and down to make sure it is not stuck or sticky. The lever should be in the down position before closing the back of the printer. If the lever is stuck or missing, the printer will generate a false paper jam message. Hope it will help you !

hp officejet 4100 all-in-one

Does the fault clear when you open/close? If it does you probably don't have a jam.
Does the machine begin to try to make copies, then stop-if so it has probably failed to feed off the tray, hence the jam message.If this is the case, pull out the paper tray, check for obstructions, clean feed rollers and try again.Are there "skid marks on the paper(indicating the rolls have turned?) If so rolls could be dirty/worn. If no skid marks, can you determine if the rolls did in fact turn? Go from there

Norman,

does the printhead run smoothly to the left side of the printer when it is powered on?

 

If the printhead cant run that freely, it will give you the paperjam message. You have to dismantle the printer again, connect the scanner and cables again when top cover is removed. Press the scanner open contact (opposite to the menu button) and watch the printhead run to the left side. It might be that either the printhead stucks somewhere on its way (press the cover of the printhead. It might be the reason) or the guide rail hinders the printhead to move.

Hi, you should check the position of paper sensor flag, called "actuator" (part number 4139 3505 02). On the picture - part 15. The "paper jam" error message means also - "toner cartidge missing", "paper out" or "photoconductor missing"