Has Voice but black screen. Solid blue LED. But menu still shows up in screen

so working on super old 2007 PC monitors. and no PC connected."? it is NOT ANY LED BACK LAMP monitor here.
came new with XP PC's.
the monitos all good to sleep mode if no PC vidoeo connected.
in the usa, even by law, (energy star)
how ever lacking a PC, the screen will show "no signal entering sleep mode"
VGA monitor.
LED = blue on, amber sleep, LED out, oFF.
NO 1080P mode allowed, (so common now) <<<< big clue here.
set the PC to 1024 x 768 (to test ) 60Hz.
using a flash light (torch) tool,.
turn on Monitor, see blue LED
point flash light to screen, see data, now, on sceen in the beam
now you now CCFL backlamps are dead. as most are this old.


Display Modes (Resolution)

640 x 350
720 x 400
640 x 480
800 x 600
832 x 624
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1440 x 900

proof BELOW. A FREE MANUAL TOO.
page 47, see 4, CCFL jacks and HV supplies here 600VDC
free service manual with full schematics and BOM

https://elektrotanya.com/lg_w1934s_flatron.pdf/download.html


in my shop I have VGA signal generator to maKE WORK EASY.

Select the input channel for your Fire TV - Turn on your TV and select the input channel for the HDMI port you used to connect your Fire TV. You should then see a loading screen with the Amazon Fire TV logo 4.

hi first you will need the proper remote control once you have this press the menu button on the remote, retune the tv hope it helps

regards
shaun

I get this too. (Love using the solid blue background)

1. Check if there are any other users logged in on the Mac.
2. Log off all the users including yourself
3. Log in only on your user account and change the background

If that doesn't work, restart first and repeat.

If even that doesn't work, change to another solid background first and then change it back to the picture.

Go to options menu on BB and locate Bluetooth.
- Enable Bluetooth.
- Then turn on Jabra 250 and Hold down the Multi-Function Button until you have a SOLID BLUE LIGHT on the LED on the headset. This could take up to 10 seconds and will take place after the LED has ceased to flash.
- Click add device on your BB.
- BB will search for your earpiece. 0000 is your passkey to add device

• Press TOOLS (the spanner symbol bottom right corner on the page that shows WHERE TO and VIEW MAP
• Press SETTINGS (The spanner symbol) or LOCALE on some models (Blue symbol in top right)
• Press LANGUAGE (the lips symbol)

This will take you to a screen with 3 items on it; TEXT LANGUAGE, VOICE and KEYBOARD
Press TEXT LANGUAGE and select American English
Press VOICE and select the name of an English speaking voice

I realise you may not be able to read the screen if it's in Spanish but by pressing all 3 you'll get the right settings.

Also if you have difficulty finding the screen with the TOOLS icon go to where you can see the map and press the MENU button in the bottom centre of the screen. This will take you to it.

LED Indicators - LaCie 2big Network
The LED indicators above the drive bays and the front LED indicate drive status and activity.
During Startup

• Front LED – blinks red/blue until both disks are powered on, then turns solid blue.
• Rear LEDs – blinks red/blue until corresponding disk is powered on, then turns solid blue.

NOTE: If the device is not able to initiate the boot process following disk startup, the front is solid red.
During Bootup

• Front LED – solid blue
• Rear LEDs – solid blue

NOTE: If a disk is failing, both the disk’s corresponding rear LED and the front LED will be solid red.
During RAID Synchronization

• Front LED – solid red
• Rear LEDs – The LED corresponding to the original disk will be blinking blue and the one being synchronized is blinking red
• Once both disks are synchronized, their corresponding rear LED and the front LED will be solid blue.

That is correct, if the lamp was bad then you will not see a picture at all. The fact that you are getting menu means the lamp is good and most likely the processor and light engine are also okay. Check other inputs to see if you have the same problem on all the inputs.

If you can get the tv to display the blue blackground(usually happens when there is no antenna or cable feed to tv) check to see if the whole screen is a solid blue, if it shows discolored areas around the screen then you might have to "demag" the screen. See if you can rent a demad coil from a tv shop and with tv on turn the coil in circular movements all over the front of screen till blue is solid.good luck!

The following procedure will re-establish the communication link between the Headphones and the Wireless adapter, this is called "pairing". Before you start please make sure both the headphones and the wireless adapter are fully charged and turned off.
Note: The headphones and the wireless adapter come pre-paired from the factory.
1. Press and hold the power button on the headphones. See Figure 1.

Figure 1

2. Continue to hold the button down until the LED starts flashing red/blue in an alternating pattern. Release the button when the LED starts flashing red/blue. See Figure 2.

Figure 2
3. Once the headphones LED is flashing red/blue, press and hold the power button on the wireless adapter. See Figure 3.

Figure 3
4. Hold down the button until the LED starts flashing red/blue in an alternating patter. The LED will blink blue, then turn off for a few seconds then blink red/blue. Release the button when the LED starts flashing red/blue. See Figure 4.

Figure 4
5. Once both the headphones LED and the adapter LED is blinking red/blue, press the volume up button once on the headphones. See Figure 5.

Figure 5
Once the headphones is paired with the adapter, the LED on the headphones will blink blue once every two seconds. See Figure 6.

Figure 6
When the adapter is paired the LED will be solid blue. See Figure 7.

Figure 7
The adapter may continue to blink red/blue for a few seconds even after the headphones LED starting blinking blue. This is normal; the adapter may take a few additional seconds before the LED turn solid blue.
Once the headphones and the adapter are paired, it is not necessary to pair them again even if the batteries on both units are completely drained.
Additional Note: Repeated pairing will not improve the sound quality or give the headphones and the adapter a cleaner connection.