Question about Roper Washing Machines

1 Answer

Roper washer will not fill on second cycle

It's fills on first cycle and drains and just sits there. I've tried the deep water wash and auto sending, but second cycle won't work

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,830 Answers

How old is your washing machine?

Posted on Jul 20, 2017

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
catriver

Ron Marek

  • 878 Answers

SOURCE: Washer won't drain

Mustache, sounds like you have a broken lid switch. No spin, no drain usually a sign of this. Check to see if the actuator is making the lid switch, or the switch itself is bad. Part number for the switch is 8318084. Catriver, post back.

Posted on Jul 30, 2006

Anonymous

  • 32 Answers

SOURCE: Frigidaire Front Load Washer

You need to replace the Motor controller speed asm part number 134149220 they are about 165.00. very easy part to replace you have to remove the back panel and the control board is on the bottom left side two scews and two plugs.

Posted on Dec 18, 2007

Anonymous

  • 2 Answers

SOURCE: ROPER RAS6233KQO T.L.W.-Won't fill/rinse with cold water

Most washers have a small screen at the water inlet valve. They can be accessed simply by revoving the hose from the back side of the washer, using a small screw driver you can carefully remove the screens and clean them out under a faucet.That may be all that is wrong.

Posted on Apr 12, 2008

Anonymous

  • 99 Answers

SOURCE: WHirlpool Waser model LSR8133HQ0 - tries to fill for rinse cycle

hellow my name is joyce and It sounds like you have a issue with your cut off valve that controls the water flow to your machine in between cycles, this is controled by your timer switch you may want to call technichian to repair. sounds like the only problem you have with the timer is on the rinse cycle not the wash cycle, but it defently needs to be fixed. if I can help you find a repair person please let me know.

thanks you and let me know if I can further assist you.
joyce

Posted on Feb 06, 2009

Anonymous

  • 2 Answers

SOURCE: washer will fill fill with water but doesn't start wash cycle

it will fill but won,t spin, will throw out water as if it washed, then it take water to rinse but won,t spin ,then will throw out water as if it did , but clothes are soaked

Posted on Feb 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just purchased ne w roper washer with auto sensing the water starts filling Ana at the same time draining water out is this normal


Probably not. It should initially activate pump but pump should cut off when filling with water. Call factory service.

Sep 29, 2018 | Roper Washing Machines

1 Answer

My Roper heavy duty 8 cycle 2 speed combination washer does not fill up on rinse cycle


when in rinse washers use just cold water so clothes don't wrinkle,try this,set the washer to just cold,start it and see if it fills or fills slowly if so you have a bad water valve on washer or no cold water going to washer.

Dec 04, 2017 | Roper Washing Machines

1 Answer

Roper top loading washer RTW440VQ1 will not stop filling up


The pressure switch, also called the water level switch, is what control the amount of water goes in the machine, If your machine is constantly filling to the overflow point, then that is your problem. Now, if water is going in and the level is staying the same then your machine drain line is lower than the pump and your siphoning out the water as it goes in. Pull the drain up a little a that should fix the problem.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_4570d45317834dd3

May 22, 2012 | Roper RAX4232KQ Top Load Washer

1 Answer

Please describe a typical washing cycle to me on the RTW4440XQ Roper 3.1 Cu. Ft. Top-Load Washer, please.


The typical cycle is;
fills to selected water level
agitates wash cycle
drains wash water
spins wash cycle
fills to selected water level on rinse cycle
agitates on rinse cycle
drains rinse water
spins final time
end of cycle

Aug 08, 2011 | Roper Washing Machines

1 Answer

Washer doesn't fill with water and begin wash cycle. I can hear it instantly draining out rather than fill, and has ran my well dry. We replaced the water pump a month ago, and it washed a few loads of...


Sounds like siphoning. This can happen if your drain pipe is too low and you run the drain hose right into it, or if there isn't any kind of air gap between the drain hose and pipe. Usually it shows up when trying to fill for the rinse cycle - it drains as fast as it fills. Or it might not fill at all. Order a "siphon break kit". They're cheap and easy to install

May 26, 2010 | Roper RAS6233KQ Top Load Washer

1 Answer

Roper washer leaks when filling


It's in the drain hose somewhere,during the fill the water gets as deep in the drain hose as it does in the washer,during the wash the pump runs in reverse keeping the water level in the hose low,during the drain the hose is filled again.
Prop the washer up in front on a couple bricks or boards,start putting in water until it starts to leak and take a peak under the machine.

Sep 27, 2009 | Washing Machines

1 Answer

Roper washer fills with water continuously


Your inlet valve is defective, can be easily changed. Approach your dealer with your model number he will direct you to the spares shop, or tell you where you can get it. Or google 'roper washing machine spares'

Feb 23, 2009 | Roper RAS8445KQ Top Load Washer

2 Answers

Error H F


this code will set for two reasons if the washer doesent start filling after 30 seconds or fills to10.5 gallons in eight minutes and the pressure sensor hasnt triped so time it and post a reply to your message letting me know which condition exist make sure your drain hose isnt too deep in your drain pipe as this will siphon water out as it fills and mke the washer think the second condition exists consult your owners manual for proper drain hose instalation

Dec 22, 2007 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

ROPER RAS6233KQO T.L.W.-Won't fill/rinse with cold water


Most washers have a small screen at the water inlet valve. They can be accessed simply by revoving the hose from the back side of the washer, using a small screw driver you can carefully remove the screens and clean them out under a faucet.That may be all that is wrong.

Oct 27, 2007 | Roper RAS8445KQ Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Roper Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Mike

Level 3 Expert

4363 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Are you a Roper Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...