Question about Makita Hm1307cb Demolition Hammer, 1 1/8 In Hex, 35 Lb 14f120

Open Question

Makita 35lb breaker wont hammer. Power light turns on but wont hammer.

We have replaced the cord previously and it's getting power but no response from the motor

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 126 Answers

SOURCE: Hoover WindTunnel Canister: Roller brush motor not turning

These motors have a fuse incorporated in the field winding and it sounds like that blew. These motors sometimes overheat at the front bearing and the bearing will melt into the plastic housing. This will cause the fuse to blow. It sounds like that's your problem. You can remove the motor by removing the three screws on the bottom of the powerhead and then check the front bearing for any bubbling or blistering in the plastic housing. The shaft of the motor should turn easily.

Posted on Jan 27, 2008

Ad

Anonymous

  • 360 Answers

SOURCE: Makita 2704 I overloaded my motor

if the motor RPM drops dramatically when the noise starts, it is probably a dry motor bushing, if this just started, lubricating the motor may just fix it.


Posted on Feb 13, 2009

Anonymous

  • 1185 Answers

SOURCE: power cord worn out where it enters motor, have to

You have popped the fuse in the plug top or have burnt out the wires in the cable

No matter you have got to shorten and re-wire the cable into the cleaner or get a new lenght of flex and do the same thing.

Some are easy to re-wire some are a pain

Posted on Aug 27, 2009

shopper12_mi

  • 1 Answer

SOURCE: Makita HP1640 hammer drill dual mode - 2 hours

Exchanged Makita HP1640 hammer drill for a new one. The 2nd drill did the same thing in under an hour!! Will return for refund. Instructions say the Forward/Reverse switch must be in a full up or down position for the Hammer/Rotary switch to move; well, it is and the Hammer/Rotary switch still stops at a 1/2 way point between modes. Although I can still use the drill, instruction warnings say not to because it may potentially burn out the motor. I'll have to go with a different brand this 3rd time around. It seems to be a design flaw.

Posted on Oct 11, 2009

rowdy45176

David Ford

  • 2176 Answers

SOURCE: How do I replace the power cord for a makita palm

without knowing what the model number is you also have to remove the pad assembly and usually you will find some there if all removed you can GENTLY pry the cover halves apart. Go to Makitatools.com with you model number and you can download a breakdown for this tool.

Posted on Mar 16, 2010

Testimonial: "Thanks for this info. The Makita tool site is helpful as is your information. I found the schematics for my model BO4510. Wish me luck. JK"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Circular saw that won't turn on ( the switch and cord are brand new )


Do you get a voltage reading from the brush holders? Have you checked the brushes, some of them have cut outs.

Jun 05, 2012 | Porter Cable Saws

1 Answer

Router won't power on. Correct adapter. No previous problems. Don't get any response from the router after plugging it in? Is it normal for routers to just have a system fail like this? Also is...


May be a button on back of router to power on/off. If you have any other electronics you can compare voltages on power cords and make sure they match and try a new power cord. Generally though with routers if it has been fried by a surge of some kind there generally isn't a way to fix it, at least not in any way that will be cheaper than just replacing the router itself.

Aug 21, 2011 | NetGear RangeMax NEXT WNR834B Wireless...

1 Answer

When I turn on the router, there is no response at mosttime, although sometime it works.


Do a check on your cord, a bad cord can cause that, either that or the power switch is missing contact and may need replaced.

Mar 06, 2011 | Milwaukee 5619 29 Router Motor 1 3/4 Max...

1 Answer

Powers on immediately powers off


ok well there is somwhere to start i would see if you can get it to take a charge ok and if it does than try to start it without the ac power on and see what it does if it wont take a charge your battery may be bad or your charging circuit may not be connected correctly ok lrt me know best regards mike

Aug 27, 2008 | Dell Inspiron 5160 Notebook

1 Answer

Accessing motor Miele Flamenco II


I had the same thing happen to my S251. Open up the vac. There is a third hidden screw in the groove where the accessory door is hinged. It's really well hidden, use a flashlight. Once its open, you'll have access to the power cord and you can test its conductivity. I didn't really believe it could be something as pedestrian as that, but the retractable power cord takes a lot of abuse, and eventually it fails. Replaced mine and the vac works great.

Jul 31, 2008 | Miele S251 Flamenco II Bagged Canister...

1 Answer

No power to vacuum motor. Switch need to replace.


See my response to "posted by bigbadben on Oct 07, 2007".

The cover that I referred to in my answer is a small plastic plate that covers the 'live' electrical bayonets between the electrical cord rewind spool and the motor. I did not make this clear in my first response. Before you start disconnecting any wires take a digital photo and/or draw yourself a electrical diagram. Save yourself a lot of time come reassembly.

Jan 02, 2008 | Electrolux UltraLux 2000 Bagged Canister...

1 Answer

Motor won't turn on


Hi , Try to check with multi tester the power cord ,test the two tips of male outlet switch on tested read the continuity /if not reading ,pulout if push type /if permanent open cover below test the test the cord inside to the male plug if does not response cord is problem,check also fuse test both end of fuse not reading fuse buste then replace thats all goodluck.

Nov 12, 2007 | KitchenAid KSB5 Professional Stainless...

1 Answer

Where do you get replacement motor for fan?


hesitate a little. the fact that the fan not spinning does not mean it is faulty. check continuity across the fan or if you can do so safely, power it direct from mains. remember a lot of these fans are unpowered when the door is open as well

Mar 30, 2007 | LG LRBN20510WW Bottom Freezer Refrigerator

Not finding what you are looking for?
Makita Hm1307cb Demolition Hammer, 1 1/8 In Hex, 35 Lb 14f120 Logo

Related Topics:

374 people viewed this question

Ask a Question

Usually answered in minutes!

Top Makita Hammering Experts

John Trevino

Level 3 Expert

1420 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2013 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

29760 Answers

Are you a Makita Hammering Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...