Dishwashers Logo

Related Topics:

Shree Posted on Jan 28, 2019
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Meiko dishwasher model 80.2 showing error 204 when water filling to the tank, give me the solutions..

1 Answer

Dennis Boxerman

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Master 1,306 Answers
  • Posted on Jul 14, 2019
Dennis Boxerman
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Feb 07, 2009
Answers
1306
Questions
1
Helped
645088
Points
2787

This is straight from the repair manual.
204 Final rinse time Parameter 4 ... 30 s. 7 Duration of booster pump activation (running time limited by P306!!).
306 Maximum final rinse time Parameter 0 ... 30 sec. Maximum booster pump running time (rinse) (limit of P204)
Booster heater pump does not work Check power supply to power rinse pump. Check pump rotor and replace 203/204 pump if necessary. Check start capacitor and replace if necessary.
Hope this is of some help.

5 Related Answers

Anonymous

  • 11 Answers
  • Posted on May 10, 2008

SOURCE: dishwasher fix

111
Floor pan Leakage
Leak inside machine activating ground float switch
302
At pumping out during rinse cycle level does not fall below level 1
Drain pump faulty, blocked, aqua stop not closing completely, no signal from circuit board (connection number 6 on XA1 connection plug)

Ad

Anonymous

  • 60 Answers
  • Posted on Jul 29, 2008

SOURCE: LE error after machine fills with water

LE actually stands for "Lock (motor) error". The main pump motor is probably bad. It is able to drain because that is a different pump motor. If it was a problem with how the drain hose was run and it was draining out you would get a DE error "drain error".

Anonymous

  • 170 Answers
  • Posted on Mar 27, 2009

SOURCE: Ge Triton XL Dishwasher Fill Problem

I would check your fill valve screen, where your water line connects to the dishwasher, lots of times i will see that screen clogged, especially on customers homes that have wells.

There is no way to change the fill time on these.
There is also the potential problem with the float sticking if it is gunked up it will not allow water in...see that it moves up and down freely and you should here a clicking noise.....If it is not one of these there could be a problem...with the timer...I am providing a link that will help walk you through this problem in a more technical...manner...if you are not comfortable performing these tests...i suggest you forego it and let a tech handle it....

http://www.applianceaid.com/dish.html#filling (http://www.applianceaid.com/dish.html#filling)

this is one continuous link.....you can scroll down until you see the won't issue.
I hope this helps ..good luck, have a good day& please rate my effort......The Fang

Anonymous

  • 170 Answers
  • Posted on May 13, 2009

SOURCE: i need an instruction manual for meiko ecostar 530f dishwasher

Go here and see if your manual is there...I hope this helps...thanks for rating my effort.....The Fang


http://www.meiko.us/downloads.htm

thebensonsmi

  • 2 Answers
  • Posted on Sep 06, 2009

SOURCE: Kitchen Aid dishwasher model KDC-18 is not filling with water

Under the machine is the water inlet valve. if you take off the front end of that you find a filter which fills up with rust, and you can clean it out. If that doesnt work, repairclinic.com will sell you a new valve for 32

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

MEIKO UPster Industrial Dishwasher. How can rectify the meiko d upster dishwadher 118 error

Question edited for clarity. Please spellcheck and Capilitalise. Always include model number.

Door Contact Switch error.

MEIKO ECOSTAR & UPSTER Troubleshooting

makewebeasy.net https://image.makewebeasy.net > Document > T... PDF 118. 201. 202. 203. 204. 205. 206. Info & ERR. - No. Description. Possible cause. EEPROM plug-in fault. • EEPROM. - Not present/defective. - Installed ...
2 pages

..
0helpful
1answer

Meiko FV40.2 Error 305?

Booster pump output low/defective, rinse nozzles clogged, wash tank level sensor soiled, moisture in sensor tube, hose kinked or not water tight
.
booster tank level sensor defective/disconnected, water inlet strainer is soiled, booster tank vent is clogged, anti siphen flap
This is per their tech manual.
I have found in some cases that the impeller on the fill motor is plastic and can become disconnected from the motor shaft.
0helpful
1answer

Meiko dishwasher DVD 80.2 showing error 202

202 Level not reached in booster tank during filling.
Level switch defective/disconnected, water turned off, inlet hose kinked, inlet strainer clogged.
Start with these basics.
0helpful
2answers

Meiko dishwasher. Do I have an eeprom problem?

sounds like it could be a defective cylinoid switch...this will not allow water to flow properly through the machine....this is located at the water connection....try replacing and reconnect water...good luck
0helpful
1answer

Error 305 on meiko dv200.2 what does it mean?

Could be a faulty booster level / pressure switch. Do you hear the air gap cup filling in the back? Could be a faulty fill solenoid (aqua stop hose with solenoid at water inlet.)
0helpful
1answer

Meiko error 901

Errors 901 and 911:
Pot washer show up alarms 901 and 911.
This alarm normally testifying loss of I/O card, faulty CPU or short circuit/earth fault on one of the sensors or actuating mechanisms.
First what we've done is replace patch cord between I/O card and Eprom. It does not solve the problem.
Once errors were appearing straight after we tried to start the cycle, we got to the point that machine could not fill up the tank with water and that pointed us to check filling solenoid (9207489).
Solenoid coil was found burned and shorten (see attached picture).
We had no original spare part and took 9727345 solenoid valve spares to temporary fix originally installed 9207489. It works now, but dripping a bit, so it must be replaced once new arrived
9207489 - original filling (supply water) solenoid valve. It is membrane type.
9727345 - solenoid valve piston type. This spare also belongs to Pot Washer, but due to it's another type it won't work on supply line, as it is too weak to open the water 9water pressure is too hight to for this valve and he could not open under the pressure). So we took only body and coil from it and inserted old spindle from 9207489 in it.
Jul 16, 2013 • Dishwashers
0helpful
2answers

MEIKO DV 80.2 ERROR CODE 305

305 Booster content is insufficient for rinsing
See error code 301, booster tank level sensor defective/disconnected, water inlet strainer is soiled, booster tank vent is clogged, anti siphen flap.
301 Level 1 not reached when filling (number of cycles exceeded)
Booster pump output low/defective, rinse nozzles clogged, wash tank level sensor soiled, moisture in sensor tube, hose kinked or not water tight.
3helpful
2answers

Meiko dv80.2 error 201

Error code 201 Indicates the incorrect water level...in that the level was not achieved during filling...check the following.

Correct water level was not reached during initial filling.

Check that the water hose is correctly attached and is free of “kinks” or pinching. Also check that the water supply is turned on.
I hope this helps...thanks for rating my effort....the Fang
1helpful
2answers

Meiko FV40.2 Error codes

212
Boiler temperature too high
Contactor faulty, probe faulty, check connection on XA5
The code 312 is the same as a code 212 as stated above.
There are dozens of error codes and you should be able to get them from your local meiko dealer, hope this helps, colin
Not finding what you are looking for?

6,742 views

Ask a Question

Usually answered in minutes!

Top Meiko Dishwashers Experts

john h

Level 3 Expert

29490 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66484 Answers

Robbie Goodwin

Level 2 Expert

384 Answers

Are you a Meiko Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...