How to turn up sewing speed - Sewing Machines

change out the switch

Repairing a Janome or New Home Sewing Machine ...

www.thriftyfun.com/Repairing-a-Janome-or-New-Home-Sewing-Machin...

Question: Memory Craft Machine Won't Run ... I'm a computer repair technician and good with tools, is this something I could fix or should we .... machine which will zig zag fine if i turn the wheel by hand or sew very slowly; as soon as I speed ...

Janome won t turn Sewing Machines Questions & Answers ...

www.fixya.com > Forum > Tags > won t turn > Sewing Machines

Janome sewing machines won t turn related questions and answers. ... Ad. Question about Memorycraft 6500P Computerized Sewing Machine ... it could be a part has worn or broken, esecially when the hand wheel won't turn,, it needs to be.

Janome wheel not turning Sewing Machines Questions ...

www.fixya.com > Forum > Tags > wheel not turning > Sewing Machines

Janome sewing machines wheel not turning related questions and answers. ... 10000 janome jamming fly wheel won't turn fly wheel won't turn warning for too thick ...the hand wheel is not moving the needle at all Hi I was unable to move the needle at all ... Janome Memory Craft 9000 Computerized Sewing Machine.

Make sure that you are running the thread through the winder tension guide before it goes bobbin winder. Best to consult your owner's manual.

Also, it helps to slow down the winding process. Slower speed winds the bobbin more consistently and does not stretch the thread as much as a fast speed will.
Beginner Guide to Sewing Sewing Machine Parts Reference Guide

...

look for the speed control knob. turning that should make it sew faster. usually it is quite big.

Hi!

Here is the user manual to this sewing machine. Hope it will help you.
https://manualsbrain.com/en/manuals/1095863

sure there isn't a knob for speed that you moved by mistake. my machine has a speed control. also if there is a foot pedal, check it out.

Is the hand wheel hard to turn? If so this could be a lot of things, anywere from needing lubrication to a siezed bushing or just a large amout of thread in the takeup lever.
You will need to remove the covers to diagnos this problem. I so I would recomend taking it to your dealer for a clean and service. If they tell you it is not repairable go somewere ells. That just means he does not no how to fix it.
If the handwheel is not hard to turn let me know.

There is no speed adjust, but 1st you must know the source of the slow down. Remove the belt from the motor pulley and run it, if it goes fast try turning the hand wheel if it is stiff the machine needs clean and oil. If it turns freely you motor may be dirty or just slow. If dirty, sometimes you can without the blet attached run it at full speed for 10 to 15 minutes. It should get faster as you run it. If not motor is weak or slow needs replace. Just replacement motor as genuine probably no longer available.

The motor running noise is because your bobbinwinder is on. Flip the bobbinwinder to the right.
Rick
Bernina rech
(don't feel dumb, it happens to many)

TRY THIS, itma not be your model, but should help Title:
How do I wind the bobbin?
Pre-tension disk Bobbin winder shaft Bobbin

1. Pull up the spool pin as far as possible, and then put a spool of thread on this pin.
2. Pass the thread around the pre-tension disk. Make sure that the thread passes under the pre- tension disk.
Pre-tension disk Pulling it in as far as possible

Caution If the spool of thread is not in the right place, the thread may tangle on the spool pin.

3. Pass the end of the thread through the hole on the bobbin from the inside of the bobbin.
4. Put the bobbin onto the bobbin winder shaft and slide the bobbin winder shaft to the right.
5. Turn the bobbin clockwise, by hand, until the spring on the shaft slides into the groove of the bobbin. Spring on the shaft Groove of the bobbin

6. Turn on the sewing machine.
7. While holding the end of the thread, gently press the foot controller or press start/ stop button (for models equipped with the start/stop button) to wind the thread around the bobbin a few times. Then stop the machine.
Note

• If the sewing machine is to be operated using the foot controller, connect the foot controller before turning on the machine.
• When the foot controller is plugged in, the start/stop button cannot be used to start sewing (only for models equipped with the start/stop button).

8. Trim the excess thread above the bobbin.
Caution Make sure you follow the instructions carefully.
If you do not cut the thread completely, and the bobbin is wound, when the thread runs low it may tangle around the bobbin and cause the needle to break.

9. Slide the sewing speed controller to the right (to set the speed to fast).
(For models equipped with the sewing speed controller.) Sewing speed controller
10. Press the foot controller or press start/stop button (for models equipped with the start/stop button) to start.
11. When the bobbin seems full and begins spinning slowly, take your foot off the foot controller or press start/stop button (for models equipped with the start/stop button).
12. Cut the thread, slide the bobbin winder shaft to the left and remove the bobbin.
13. Slide the sewing speed controller back to its original position (for models equipped with the sewing speed controller).


Caution Not winding the bobbin properly may cause the thread tension to loosen, and may break the needle.
Wound evenly Wound poorly


Note

• When the sewing machine is started or the handwheel is turned after winding the thread around the bobbin, the machine will make a clicking sound; this is not a malfunction.
• The needle bar does not move when you slide the bobbin winding shaft to the right.