Where can I get a handle bar for a model 80-kb1208

ebay

The charger socket is at the back of the Lil rider under the top box. If you go online and type in Lil Rider there is a You Tube video showing assembly. At 7:30 mins in the seat is fitted and the presenter lifts the Bike and shows the charge socket. I don't think this is exactly the model you have but I would hope there is not too much difference.

If you are sure that you have a really bright glow from your glow bar, then check the coils on the gas valve. Also, check the flame/radiant sensor.


Valve coil kit 279834
Glow bar igniter 279311
Replacement Radiant sensor 338906 for KENMORE Laundry Appliances...

Good luck

screw adjuster all way in on handle bar,feed through bike to clutch arm,hook end nipple, then unscrew lever adjuster out until firm then adjust accordingly.

Remove the cable from completely and thread it through from front to back.

It can be a little tricky!

If you are referring to chain break band

Tools you will need:
1/2 Socket (to remove bar nuts)
T25(torq) or you can use a Flathead screw driver but is a little harder.

Remove 2 bar nuts,Clutch cover,bar,chain, 2 screws on black bar handle right behind clutch cover(this is needed because there is a hidden screw there for the chain break) You will need a new chain brake (my guess is that it is part # 530071893 aprox $15) but you will want to verify that with your model number.

You should see the chain break assembly, 3 - T25 screws are visible after the clutch cover is removed(note sometimes you have to clean saw dust to make screw head visible) the other T25 screw is hidden under the black bar handle. Once you remove all 4 screws on the chain brake you will be able to pull it off.

Installing the new one is the tricky part because if it is set(or break is on) you will have a hard time putting it on.One of the easiest ways is to focus on it near the muffler you will see that a metal 3 pronged gear fits into the plastic part of the chain break handle.and if the band is too tight to fit over the clutch drum you will have to carefully reset it by applying pressure onto the area that has the 3 pronged gear and chain break handle make sure that the handle is pushed forward all the way while you apply pressure then slowly pull chain break handle back till you hear a "snap" this resets the chain brake spring and the band should now fit over the clutch drum.Now, proceed with putting back together 4 chain brake assembly screws,2 handle screws,and bar,chain,clutch cover,and 2 bar nuts.

Please note it is important that you apply quite a bit of pressure onto chain break area where metal (3 pronged) gear fits into handle while resetting or when you reset it the metal part can cut into and damage the plastic piece in the chain break handle.

You can see a breakdown here: http://www.searspartsdirect.com/partsdirect/part-model/Poulan-Parts/Chainsaw-Parts/Model-P4018WT/1324/1503220/P0506041/00002?blt=06&prst=0&shdMod=P4018WT

Hope this helps!

This sounds like an electrical problem. On some of their models they had an issue with the wiring on the handle bars. This was noticed when the handle bars were turned in one direction and the machine would shut off. Look around and down the handle bars for damaged wiring.

Clcik on the link below and you can buy a metal door handle for your 1995 Ford F150 XLT

http://shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=1995+ford+F150+door+handle&_sacat=See-All-Categories

http://cgi.ebay.com/ebaymotors/Bronco-F150-F250-80-96-Chrome-Exterior-Door-Handle-LH-_W0QQcmdZViewItemQQfitsZYearQ3a1995Q7cMakeQ3aFordQ7cModelQ3aFQ2d150QQhashZitem483d523ce6QQitemZ310266445030QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

this could be caused by wheel balance being off or poss unevenly worn / damaged tyres and poss wear at the head stock bearings

YOU MAY HAVE A POSSIBLE BAD BELT OR THE MOTOR THAT RUNS THE BAR MAY BE BAD, THE OTHER POSSIBILITY IS THE SWITCH THAT TURNS ON THE BAR MAY BE BAD. OR A WIRE COULD HAVE COME OFF THE MOTOR. i THINK YOU DO KNOW THAT THE BEATER BAR DOES NOT RUN WHEN ON WOOD FLOORS.