How do I stop the error E2 code on my washer? I

Never heard of the make 'Haam"? Perhaps you mean 'Haier'? Anyway, it might be a generic drain error

An E2 Error code indicates that the washer is still draining after 8 minutes. Check the following: Check that the drain hose is not more than 391 ?3" (100 cm) from the floor. Remove any clogs from the drain hose.

E2 - Error Code - Stacked Laundry Center - Product Help

3. Toshib washing machine error code:

1. E1 : Water discharge error.
2. E2 : Safety lock error (Door switch).
3. E3 : Laundry is unevenly distributed inside the washing bucket.
4. E3 : Laundry is misaligned, cage screws are loose, the balance ring is open, the clutch is loose, the door switch loses the spring (due to the screwing of the cheek), the switch wire is blocked, the safety lever is blocked. .
5. E4 : Damn buoy.
6. E5 : Water supply error.
7. E6 : Washer motor, too much, low water level, clutch shaft, clutch shaft.
8. Ec1 : Many laundry or little water.
9. Ec3 : Many laundry or little water.
10. Ec5 : Many laundry or little water.
11. Ec6 : Many laundry or little water.
12. F : Multi-wash or charring.
13. E7 : Washing motor jam, too much, low water level, clutch shaft, sanso clutch.
14. E7-1 : Memory overflow error, programming: press the water level, timer, discharge, open the power, and the pip pip remove the power and about 1 minute of the pin works well.
15. E7-4 : Word count error.
16. E8 : Washing motor jam, too much, low water level, clutch shaft, sanso clutch shaft.
17. E9 : Water leaks, the washing bucket is broken, the valve is stuck, entangled with the senso of the broken water, do not forget to check the wires.

https://www.youtube.com/watch?v=dkMCdjJdKRs
The E1 or E2 error code is an Auto-Stop Protection Error, indicating an issue detected by a sensor. This error code will require service. The E3 error code displays when an Abnormal Operation Protection Error has occurred, and activates to protect the unit from damage. This error code will require service.
https://www.lg.com/us/support/help-library/e1-e2-or-e3-error-code-CT10000014-1340721215523
In this case, you need to drain water and remove the laundry. Then, run the rinse mode to clean the drum. Next, start the technique to make sure that the OC error has disappeared. If the washing machine is not correctly connected to the drain hose, OE, OF, E3 will appear on display.
https://all-errors.com/samsung-washing-machine-error-code-e3/

Hi, the E2 F9 error means that the communication between the pump and the control board is failing. It could be a bad wire connection between the pump and control board, or your main control board is bad and needs to be replaced. First you'll want to check for a clog in the drain. You can easily youtube how to.
Best of luck.

Ned

Toshiba top load washers have standard error codes. Depending on the display (2 or 3 digits depending on the model) it will either show E21 (or E23) or alternate E2 and -1 (or E2 and -3). Here's a list of most Toshiba washers error codes;

E1: Water doesn't drain in time or not at all
E21: Lid open
E23: Lid not locking
E31: Load imbalance
E32: Check E1 and/or E31
E5: No water coming in

You can try resetting to factory default by following the procedure: Power OFF, then pressing and holding the Super Spin Dry button, press power ON and it should beep 3 times. E2 error code aw 8990st toshiba wash Washing Machines

There are 5 pins on the socket in the base. on the back of that
socket there is a black strap that holds the wires in. it snaps off
and the wires drop out. you need two small washers remove the two screws push the wires replace the strap now put the two small washers the screws and replace job done

your main control board is having a problem need to have service rereplace it free of charge and the board has been upgraded

either any of the key(button)is got stuck up prtessed or the motor of the washer is got weak.due to this e2 error code shows up.the washer works if the motor is weak but if there are more clothes in the washer and due to that motor cannot spin properly so it shows e2.First clean the washer internally after emptying it completely then check.if still e2 error then motor needs replacement . you can get new motor at www.repairclinic.com

The machine beeps E2 all the time. Actually E2 error code means washer door is not closed properly. However washer door does close properly, but the machine still beeps with showing E2 error code. Please help solve this problem.

Many thanks,

Robert