Question about Peavey Music

1 Answer

Peavey max 115 has sound on earphone but no sound on speaker but speaker is good.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 674 Answers

Have it looked at - there is probably some chip that is burned out in the output section.

Posted on Sep 30, 2019

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Fred Yearian

  • 5603 Answers

SOURCE: Peavey 115 Low hum Low volume from input

The preamp section has a problem. It could be anything in the preamp but is OFTEN the input jack itself. They take a lot of abuse.

Also the insert jack contacts that forward the preamp to the power amp if no external FX are used can go bad.

Additional things are circuit board cracks caused by rough handling and also controls that have had the knobs mashed in which can destroy the potentiometers they are connected to.

Posted on Sep 22, 2009

Fred Yearian

  • 5603 Answers

SOURCE: I have a Peavey PV 115 Speaker...The horn works

Check the resistance across the woofer connection points. Using an ohmmeter, you should se around 6 to 8 ohms. If there is no continuity, you have a blown speaker.

Posted on Jun 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need schematic for peavey max 115-chi-imp-120v bass amp serial # 0dajk050437


http://www.peavey.com/support/searchmanuals/
Owner's manuals and spec sheets that are not available on our web site may be obtained by mail (via money order) or by phone (via credit card). Spec sheets and schematics are $2.50 per copy, and owner's manuals are $7.50 (paperback) and $20 (notebook).
Send Money Order to:
Peavey Electronics Parts Department
PO Box 2898
Meridian, MS 39302
Credit Card orders by phone:
1-877-732-8391

Sep 24, 2017 | Peavey Music

1 Answer

Peavey Problems


Check speaker impedance or disconnect speaker leads, then use a 9V battery to verify cone movement and if this test is ok, then go inside the amp, if there's no fuses blown check opamps supply voltage which should be -15V at pin-4 and +15V at pin-8, let me know your results to help improvement.

May 21, 2013 | Peavey Electronics Peavey Max 112 Bass...

1 Answer

I have a Peavey PV 115 Speaker...The horn works and the fuses are good ..The wiring looks and feel tight BUT the 15" speaker will not work...Any ideas ???


Check the resistance across the woofer connection points. Using an ohmmeter, you should se around 6 to 8 ohms. If there is no continuity, you have a blown speaker.

Jun 25, 2011 | Peavey PV 115 Speaker PA Passive

1 Answer

I have a two way peavey p115 speaker system and audio has stopped coming out of the high frequency driver . I tested the high frequency driver with a multi meter and it is fines.I also have a working...


Testing the driver with an ohmmeter is incomplete test. Sometimes the magnets break off the drivers rendering no sound. Sometimes the voice coil shorts and if you don't interpret the ohmmeter readings correctly you can overlook a faulty driver. Remove the horn and look for damage such as lost magnet from the back. Also the peavey cabs have a protection circuit so if you did not try another speaker to the same wores going to the driver, it may be the Polyfuse on the protection circuit or other components.

May 02, 2011 | Peavey PV 115 Speaker PA Passive

1 Answer

I have 2 peavey 900 Power Amplifiers i would like to link them together was wondering what is the input wattage it can handle?? not wanting to mess anything up!


You CANNOT link the outputs of the amps. They need to drive seperate speakers.

You can tie the inputs together so they will send the same sound to their seperate speakers.

Max power for the Peavey 900 is 900 Watts RMS into a 4 ohm speaker in Bridge mode... That is enough to blow many speakers.

May 15, 2010 | Peavey Pv 2600 Power Amplifier

Not finding what you are looking for?
Music Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peavey Music Experts

Michial Gueffroy

Level 3 Expert

1140 Answers

PNiss

Level 2 Expert

151 Answers

The Knight
The Knight

Level 3 Expert

76171 Answers

Are you a Peavey Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...