Question about Samsung Washing Machines

Open Question

Red key on Samsung washer showing all the time

Washer wont do anything

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: maytag washer panel show a

Try the "End of Cycle" button to the right of panel front, next to Start button. Mine says hold for three seconds to lock/ unlock control.

Posted on Oct 13, 2008

Ad

Anonymous

  • 8 Answers

SOURCE: My washer wont do anything but fill up with water.

Could be a bad belt or a bad lid safety switch.

Posted on Jan 22, 2009

TheMobilian

Dan Webster

  • 8220 Answers

SOURCE: Help! My Samsung Washer wont

Water Level Sensor Trouble.
(When the input signal from the water level sensor is out of
range, the unit will send out beeping sounds and halts the
cycle.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Posted on Sep 10, 2009

frankgilbert

Frank Gilbert

  • 613 Answers

SOURCE: my frigidaire washer shows a loc code and it wont

You have to call them and get the code. Have proper id and all ready.

Posted on Nov 02, 2010

Dwayne Hoo-Fong

  • 403 Answers

SOURCE: f71 code shows up and the washer wont do anything

Motor Control Unit Error

The Central Control Unit has detected a short in the motor control unit.


Potential Causes

•Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU)

•Check the MCU

•Check the Drive Motor

•Check the Wire Harness

Posted on Feb 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Samsung washer error code 8C


I show an EC code as a temperature sensor issue. Turn your washer off at the mains, wait 30 seconds, turn mains power back on and start a new programme. If that doesn't work, it's time for a service call.
I did not find anything for an 8C code.

Jan 26, 2017 | Samsung Washing Machines

1 Answer

Samsung WA5451ANW top will not open. Code


Have you tried to tilt the washer? When I tilted my washer 15 - 30 degrees and then I could open the lid. My problem was that I had a clogged filter I have not seen before.

Aug 30, 2017 | Samsung WA5451ANW 4.7 cu. ft. Top-Load...

1 Answer

Whats the red key and circle llso shows a OE code on LG steam washer wm2487hwm


OE on the LG means the washer is not draining or has a draining issue. When it happened to me I started by manually draining the washer and then running a spin cycle. In a pinch the work around was OK but I could never be certain the wash was complete. Also the wife hated it.

Finally, I dug in and went for a fix. All the hoses were clear and the pump seemed to be working (also the pump screen needed clearing). I found the problem to be a breather hose that runs from the top of the drum to one of the drain hoses. It was plugged and I took it off and blew it out. Problem solved.

Aug 05, 2012 | LG Washing Machines

1 Answer

Samsung washer front load willnot rinse - no water coming out of hose to drain. E2 shows up


Hello,It is drain pump error. Possible solution:
• Clean the debris filter.
• Make sure the drainage hose is installed correctly.
If wont help you need to look in drain pump/wiring
More information about error codes here:
http://downloadcenter.samsung.com/content/UM/200411/20041124151342484_B1515-01527B-0603.pdf#search=%22samsung%20big%20wash%20b1415j%22

Thanks

May 31, 2010 | Samsung WF337AA Front Load Washer

2 Answers

Kenmore 90 washer won't drain


ckd pump traps for debris on kenmore remove front panel on samsung i think a rear approach is best

Jun 03, 2008 | Samsung WF337AA Front Load Washer

1 Answer

Please help , tell me why door is locked, on h 2 kenmore washer,


THANK YOU,
still nothing,

red doorlock light on, wont do anything,

I have to unplug so it will shut off,

when I plug in and hit start, red light stays on again,

Mar 28, 2008 | Kenmore 4292x Front Load Washer

4 Answers

Samsung Washing machine fault


I have foud a solution 4E error for my Samsung WD7101CKW. Water that comes inside washer is splitted in splitter with valves. One of these valves has a red label on it - this is a valve with restrictor of flow inside. This restrictor is used to limit flow speed mainly for testing purposes of pressure/water level sensor. Because of that restrictor (red cap with two holes of 0,5 mm diameter) blocked flow too much, after some time washer controller thinks that water has too low pressure.
Unplug washer, disassemble hoses from valves, disassemble valves from the washer (screwdriver needed), drill both holes in red restrictor to 1 mm (use 1 mm drill or just big needle). Assemble in reverse. Will work :)
Greetings - Thomas

Jan 16, 2008 | Samsung WF203ANW Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Washing Machines Experts

The Knight
The Knight

Level 3 Expert

76177 Answers

Paul

Level 2 Expert

381 Answers

Eric Rotmil
Eric Rotmil

Level 3 Expert

587 Answers

Are you a Samsung Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...