Question about Jackhammer Hammering

Open Question

The strike is not working anymore on my Jackhammer the motor runs fine what's causing this

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My bosch jackhammer suddenly stopped working. What the most likely cause? stop


It probably went on strike to demand more money and/or more benefits.

Apr 25, 2017 | Bosch Hammering

1 Answer

Why my Bosch brute jackhammer only hums when I press trigger? Can someone help me please?


seems as if the jackhammer motor is locked up and frozen might wanna be careful opening it up and freeing that motor up while its unplugged

Apr 17, 2017 | Bosch Hammering

1 Answer

What causes a condensing unit to run but blower motor will not come on


Most common cause is the capacitor. The top where the wires plug on should be flat. A lightening strike or other power surge will zap it and cause the top to puff up.

Aug 04, 2014 | Heating & Cooling

2 Answers

Hello, our fridge has stopped working, the fan and motor are still running but the unit wont get cold anymore.I think it might be a freon problem but I cant be sure. The motor and fan are running constant


Your right! A freon leakage system problem cause no cold anymore.
But a temp control must be check.
A defective temp control will also cause no cold of the freezer.
The same also if compressor motor is defective even though it is running.
Call a service technician to verify the trouble of your fridge.
I hope I give you idea regarding your fridge problem.

Jun 28, 2011 | Whirlpool ET1MHKXM Top Freezer...

1 Answer

Hi i have a mtx jackhammer JH202 amp and a mtx jackhammer jJH5510D sub and every so often when a song is playing there will be bass and al of a sudden it will shut off and after a few minutes it will come...


The problem was caused by you trying to run a 2OHM load on an amplifier which is designed to run only on 4OHM when it is bridged, the amplifier is most definatley cooked. An authorized MTX technician should take a look at it, to determine just how wide spread the damage is.
dreamsystems.

Feb 11, 2011 | MTX JackHammer JH202 Car Audio Amplifier

1 Answer

Jackhammer quit in middle of use


if it is an electric jack hammer the brushes in the motor maybe worn out. most ace hardware stores have a good selection of motor brushes. also check to see if the brush retension screw came loose this would also cause the same problem.

May 21, 2009 | Hammering

1 Answer

I have a old electric 120vac jackhammer (not sure manf.)


usally their is grease packed in the hammer part,you can usally see a plastic type bung(plug)on outter casing

May 13, 2009 | Electric Demolition Jackhammer

2 Answers

"jackhammer" sound coming from my washer


# Balance the load
# Level the machine
# Inspect the water pump for a blockage
# Inspect the coupling
# Inspect the transmission
# Adjust the drive belt tension
# Check the motor bearings
# Check the drum brakes

Jan 09, 2009 | Washing Machines

1 Answer

97 mazda truck wipers wont work


the motor ground is controlled by a solid state control module called the GEM (Generic lectronic Module), it is most likey burned out by the voltage surge of the strike, it is behind the radio, about 2" square and black plastic case

Jan 08, 2009 | 2007 Mazda B4000

Not finding what you are looking for?
Hammering Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jackhammer Hammering Experts

John Trevino

Level 3 Expert

1420 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2012 Answers

Tom Chichester

Level 3 Expert

54838 Answers

Are you a Jackhammer Hammering Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...