Question about Maytag Washing Machines

Open Question

Maytag MHW6000XG2 front load washer diagram and/or instructions for line fuse replacement

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
aborcass

Ron Coons

  • 2651 Answers

SOURCE: Torn bellow on Maytag front load washer

there is a spring style clamp holding it to the front panel simply peel back slightly and "pop" it off, then holding it to the inner tub is a screw style clamp, depending on yr of production, either a 5/32 scrwe or a phillips, holding it in the 2 oclock position, release clamp andreinstall boot, it might take some time to get to fit backaround hte tub but itll bo, you gotta walk it on in spots ( like changing a tireon the bikes as a kid) itlll strectch over the rim and fit, just have to work it

Posted on Dec 03, 2008

Ad
aborcass

Ron Coons

  • 2651 Answers

SOURCE: maytag Neptune front loader rubber boot replacement

can be done just need PATIENCE!.. youll need ot remove the door assembly, and the 2 screws oppisirethe heing willalow for the front "u" shaped panel to be reomved.. next remove the 4 screws from with in the dispenser area, and then there are perhaps (6) 5/16 screws holding the nextfront bulkead and maintop assy down.. after removing theese screrws youll be able to lift eh main top back wards( prop it with something, a few more screws will release te hlatch assembly.. from here you can probably install the new bellow, remove the spring and wire, and the work the new bellow around the tub lip. a third hand will come in handy, after working it around , youll needto reconnect the tension spring..HARDEST PART OF JOB>>> REQUIRES PATIENCE!!!!!. sometimes this goes on for me with out issue in 5 min, other times 25 min and im PISSED AT IT!!!!!!!,, wrap the wirer around bottom of lip and your going to hold one end of spring, needlenose vice grips work perfectly. then with another set of needle nose. stretchthe spring togethr to lock the wire around.. whern you finally get this reassemble the latch and drop the top back down replace all teh screws, and finally you need to retuck the bellow into the front bulkhead( tabbs line it up nicley.. good luck!!!

Posted on Feb 22, 2009

aborcass

Ron Coons

  • 2651 Answers

SOURCE: I need a diagram for a maytag neptune mah5500bbw washer

here you go!

http://www.servicematters.com/maytag_library/docs/16026186.pdf

Posted on Mar 20, 2009

Anonymous

  • 1 Answer

SOURCE: replacing door gasket on maytag neptune MAH5500BWW washer

I need to know what are the steps to replacing the door gasket, I would like to know what to take apart, and what not to take apart. Like a step by step lay out.

Posted on May 25, 2009

erica graber

  • 530 Answers

SOURCE: I need to replace the molding door boot seal on my

you need to first unplug the unit. next you need to remove 4 screws that hold the dispenser lid on. next open the door remove 4 screws. remove the door and the out side panel. next located to the top left and right you will see a bracket with a 5/16 bolt remove them and take the bracket off. next lift the lid. you will have access to the door seal. you will see a spring at the top that is the band that holds the seal to the tub. the front of the seal just peels off. when putting the band and spring back on may be a little tricky. get one side up to the top gett a piece of duct tape and secure it. so that you can properly get the rest of the band on without fighting with it. get some vise grips and pull the spring over and attach to the part that is tapped. let me know if this helps or if you need more instructions.

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag neptune washer can not change the wash cycles


1) test the timer probably faulty,tight connection wires see the diagram how to test,and see the diagram in line black, how the contacts from timer control everthing in the washer.
2) problem of cold water, is the cold water turn on? consult your owner manual for to see if acting abnormally
3) check the selector is o.k
God bless you

7_19_2012_9_38_07_am.gif7_19_2012_9_38_25_am.gif

Jul 18, 2012 | Maytag Neptune MAH6500A Front Load Washer

1 Answer

Maytag front load washer, MHW 3000 series, f22 error message


This is a problem with the door not locking shut. Maytag have an ecellent technical assistance page on this problem with diagrams and stuff. Go to:

http://maytag.custhelp.com/app/answers/detail/a_id/2889/~/display-shows-f22-or-fdl---front-load-washer

and take a look

Jun 30, 2011 | Maytag Washing Machines

1 Answer

Top Load Stacked Washer / Dryer Maytag lse7806ace -- washer will not run, except in spin cycle


I believe there is a fuse on the left side front under the front panel about a foot from the top of the washer.

Nov 20, 2010 | Maytag LSE7806A Top Load Stacked...

2 Answers

My maytag washer stoped during the cycle with 8


You may have blown the internal fuse located in the lid switch. Could be you over loaded the washer and blew the fuse.
Unplug the washer and remove the four screws holding the control panel front in place. Two screws on top and two screws under control panel.
Remove the control panel and tilt forward.
Locate the lid switch assemble and remove glass fuse and inspect.
Door switch assembly should be replaced. When you order the proper fuse it should come with the door switch assembly.
Replace assembly. Reinstall the front control panel and four screws.
Plug machine in and test.

Jan 03, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Shut the door and will not lock after given time which results in not draining or spinning. this is a maytag neptune front loading washer


It is probably the control panel on the washer. A common problem. You can actually repair it yourself with a kit and also you will need to replace the wax motor or you will have the same problem over and over. Once the wax motor is replaced it should not happen again but in the meantime you have two components on the control board which you can replace with basic soldering (sp) skills. You can actually view a free instructional video on line - if you search wax motor you will find the site

Aug 16, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Washer does not drain


ND error means no drain. When this happens it is usually a problem with the drain pump assembly, located under the bottom panel, inside the machine.

check the drain hose and the drain lines, ensure they are not obstructed. Probably the drain pump need replacement.

Oct 12, 2008 | Maytag Neptune MAH5500B Front Load Washer

2 Answers

Replacikng the belt


Searching on line is a good way to find parts and some diagrams. For me to assist you I need a make and model number. With this I can walk you through the repair step-by-step

May 27, 2008 | Maytag Legacy Series Top Load Washer

1 Answer

Maytag stackable w/d


Yes, it is inside the front washer lower front panel. Turn off poawer to unit and change w/ 1Amp 250V (regular of slow-blow). Then try only opening washer lid door with full dial pushed in (that would be the 'off' position. Only open/close lid w/ dial in off position. If washer works normally, may have a temp solution. Mine started this way, but ultimately the double relayed door lid switch was going bad and I had to replace it. Instructions/pictures below. Good Luck

AT702

Jan 27, 2008 | Maytag LSE7806A Top Load Stacked...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...