Question about Kenmore Washing Machines
I had just installed a pedestal. I unplugged the machine, tipped it over on its side and installed the pedestal. I tipped the machine up, plugged it in and pressed the power button. It beeped 3 times, but no lights or display came on the front panel. I was able to enter diagnostic mode by pressing and holding any button for 3 seconds, repeating this 3 times. This is what I observed in diagnostic mode: All lights on front panel came on, Display showed C00, Display showed U01, Display showed U00, Display showed C00, Display showed n00, All lights went off except for the Modifiers lights, Display showed C00.
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
FWIW ... the Sears guy came by yesterday. The problem was apparently that the door latch was not operating to the extent that the sensors thought the door was open. He is replacing the latch next week. He adjusted the old one in the mean tiome and it appears to be working fine.
This kind of stunned me, since my wife reported an electric zap and the interior light burned out as the dryer went dead -- so I was sure it would be a fried circuit board -- but, no, a little jiggling of the latch seemed to clear it up....
Posted on Jul 10, 2008
Uh oh! It did it again! This time I had to unplug 6 times for one cycle. Seems to be on the last 2 minutes most of the time. Today my husband is taking the control unit and looking for soldering problems. On Askmehelpdesk.com this man told of taking the bottom panel off and there is a little black latch thingy you pull to open the door lock manually. Also he said that the K2 and K4 relays are usually the problem if it isn't a soldering issue on the connectors. ( On the CCU);. He said one of them is usually burned and to clean it off and then switch it with the other one which carries less voltage, therefore doesn't burn. You can use a pencil eraser to do this. My husband told me they did this in the Army for MOose code contacts. He just told lme the soldeirng looks good on the connectors and is now working on the K2 and K4 relays. If you go to Askmehelpdesk.com/appliances you will see these tips are for the Whirlpool Duet whic is apparently the same machine as our Sears Kenmore H4's. Gosh, I hope this helps someone as it sure is not fun trying to track this problem down. I am glad you got Sears to come out. I will NEVER and I repeat NEVER buy from Sears again! Did I mention I wrote a letter months ago when I was having a hard time getting warranty work done.( Which I never did) that I had written to the pPesident, CFO and the Texas Attorney General for Consulmer Protection Division and never got a response from anyone?
Posted on Feb 14, 2009
usually if it's you motor controller it should stil go into diagnostic mode. so that is probably not your problem. can you post a picture of the inside ccu board and of the door lock this would be helpful.
Posted on Apr 22, 2009
SOURCE: our machine's digital display reads 'dE' seconds after pressing start and nothing isour machine's digital display reads 'dE' seconds after pressing start and nothing is happening except for an awful b
try to close dorr completely if not call in service tech.
Posted on Apr 29, 2009
Tips for a great answer:
Dec 02, 2013 | Frigidaire GLTF2940ES Front Load Washer
Jan 23, 2012 | Cars & Trucks
This issue usually occurs due to kinked drain pipe, clogged
drain filter or drain pump. First make sure that the drain is not clogged and
remove clogs if present. If no visible lint is present then remove the lower
front access panel to check the drain filter and drain pump for any clogs,
you'll need to clean the drain filter and drain pump completely. Hope this
helps... Please post back for any further assistance.
Aug 31, 2011 | Kenmore Washing Machines
Aug 04, 2011 | Whirlpool GHW9400 Duet Washer
Jan 03, 2011 | Siemens WFXD5200UC Front Load Washer
Sep 02, 2010 | LG WM2277H Front Load Washer
Jan 13, 2010 | Maytag EPIC MFW9700S Front Load Washer
Nov 23, 2009 | Maytag EPIC MFW9700S Front Load Washer
Oct 03, 2009 | Kenmore 15.5 in. Pedestal
Nov 20, 2019 | Kenmore Washing Machines
46 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: