Question about Samsung Washing Machines

Open Question

Where is water fill valve on rf263teaew samsung frig

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does Code nf on washer machine Samsung vrt model mean


NF indicates no water flow. This could mean that the incoming water valves were shut-off, the incoming water flow is low, or that the washer didn't detect the water flow into the washer correctly. If the drain hose is too low, the washer could fill and drain simultaneously. This can also cause the problem.

First if the washer is not getting any water, then check your shut-off valves and the hoses. Disconnect the hoses from the washer and place a bucket under them. Check the flow by turning on each valve for a bit. Clean or replace the filters at the shut-off valves and in the washer. Consider replacing the hoses. Some anti-flood hoses will reduce the water flow if they detect leaks. Make sure that the hoses are not kinked. If the water flow is good at the shut-off valves, then the inlet valve may have failed in the closed position.

If water is filling the washer, then the problem is in the water flow detection system. This could indicate the small reed switch is damaged, the air tube to the reed switch is clogged or that tube has a hole in it. Some washers check for fill by the change in the drum weight. This signal may not be reaching the control unit due to a problem with the sensor or the wiring.

If the washer is filling and draining, pull your drain hose up. It is below the washer fill level. This creates a vacuum that will drain the washer.

I hope this helps.

Cindy Wells

Aug 25, 2017 | Samsung Washing Machines

1 Answer

My samsung machine doesn't fill with water


check and test the inlet valve with a meter for voltage and for ohms see pics may also want to check the water pressure switch and the hose tubing going into it




samsung-machine-doesnt-fill-water-5xsig0kahrbrpc1dmto2pfhz-4-0.jpg

samsung-machine-doesnt-fill-water-5xsig0kahrbrpc1dmto2pfhz-4-2.jpg

samsung-machine-doesnt-fill-water-5xsig0kahrbrpc1dmto2pfhz-4-5.jpg

samsung-machine-doesnt-fill-water-5xsig0kahrbrpc1dmto2pfhz-4-9.jpg

samsung-machine-doesnt-fill-water-5xsig0kahrbrpc1dmto2pfhz-4-14.jpg

Jun 16, 2015 | Samsung Washing Machines

1 Answer

Errpr code 4e on samsun aqua jet vrt


A 4E code on Samsung washers means that the washer isn't filling properly or the sensor isn't detecting the water flow. First, make sure that the water shut-off valves are open. Next make sure that the drain hose outlet is positioned above the fill level of the washer. (This avoids the water being suctioned out of the tub.)

Turn off the shut-off valves and disconnect the fill hoses from the washer and the valves. Clean the filters in the washer and at the valves. Reconnect the hoses to the valve and place a bucket under the other end. Open the valves and check that you have good water flow from both hoses. You may want to replace the hoses. (Some washer fill hoses are designed to clamp shut if they detect a leak. This anti-burst feature will reduce the water flow to a trickle. Since the washer fill sensor detects the amount of water in the tub within 8 minutes, that will trip the error.)

If the washer isn't filling and there is plenty of water coming from the water line, the fill valve probably failed in the closed position. If the water level is rising, then the sensor is probably faulty.

Please add a comment with the full model number of your washer. Then I may be able to point you to the parts. If the washer is under warranty, contact Samsung.

I hope this helps.

Cindy Wells

May 01, 2015 | Washing Machines

1 Answer

I have a Samsung top load washer #WA5451ANW. Will only fill with water. Had to turn the power off so machine would stop filling with water.


Possible that the cut off to the Inlet valve has failed which means that the controller unit is a suspect. Also if the inlet valve is staying ON even when the power is cut off , then it is a case of inlet valve failure.

Dec 31, 2012 | Samsung WA5451ANW 4.7 Cu. Ft. White...

1 Answer

Icemaker won't fill tray,


Was the inlet tube frozen. If so your water inlet valve on the back where the water supply comes in is probably leaking and when the water reaches the freezer it freezes, blocking the inlet tube. Replace the water inlet valve.
You can Try swapping the wires on the dual water inlet valve. Then try the water dispenser. The water should go to the ice maker. This will tell you weather or not the ice maker valve is working and if the line is clear.

Aug 29, 2009 | Samsung RS2630WW Side by Side Refrigerator

1 Answer

Samsung wf328aaw


According to Samsung:

Your Washer has tried to fill but
was unsuccessful.

Make sure the water faucets are open all the
way. Check for kinked hoses.
Check the inlet screens on the fill hoses.


Of course, other things can cause the same code. Timer not supplying power to the water solenoids, solenoid water valve is defective, etc.
I would try hot fill, cold fill, warm fill. The above are the obvious.

Mr Boo


You can download the manual at:
http://www.samsung.com/us/support/download/supportDown.do?group=homeappliances&type=washersdryers&subtype=washers&model_nm=WF328AAW&mType=UM&dType=D&vType=R

Nov 23, 2008 | Samsung WF328AA Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Washing Machines Experts

The Knight
The Knight

Level 3 Expert

76171 Answers

Paul

Level 2 Expert

381 Answers

Eric Rotmil
Eric Rotmil

Level 3 Expert

587 Answers

Are you a Samsung Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...