Question about Maytag PAV2300 Top Load Washer

Open Question

GE Washer - Water fills but doesn't start cycle.

The problem started on super load, then large, and now is starting to happen on medium load as well. Water will fill to a level and stops the cycle. This would happen prior to the wash cycle or prior to a rinse cycle.
Pushing Start would reset to the beginning of the cycle.

Whether it is related or not, the fill time seems to be quite long.

Posted by on

Ad

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1028 Answers

SOURCE: maytag washer water doesnt stop

raise top or remove front panel(can't remember which) rear corner left small hose attached to connector on tub pull and clean probably plugged up with crud also ck connection on tub

Posted on Dec 13, 2008

Ad

Anonymous

  • 2 Answers

SOURCE: Load size, spin cycle, and other cycles do not work properly

error code f 06 keeps coming up and we cannnot afford to have it serviced at this time we were told it had something to do with the control panel

Posted on Mar 22, 2009

Healeyman

mike kirschbaum

  • 1198 Answers

SOURCE: Maytag top loading washer fills up but won't stop

Check the fill control device and the tube that goes to it. Make sure there is not any debris in the outer tub where the tube connects. You may be able to push the drum aside to check.

Posted on May 04, 2009

Anonymous

  • 58 Answers

SOURCE: Washer stopped at begin of wash cycle

The problem seems to lie in the rubber backed mat. If the rubber has begun to peel of the mat it often-times get stuck in the drain pump. The best thing to do at this point is to disconnect the electrical cord, open up the machine, drain out the water as best as possible disconnect the power cord to the drain and the hoses. Clean out the drain pump. reassemble. You should be good to go., Unless the drain pump is burned out (left running plugged up too long) if thats the case, replacement of the pump may be neccessary.... Hope this helps...Good luck!.... Bill

Posted on May 18, 2009

Anonymous

  • 88 Answers

SOURCE: older maytag wahser water level and agitate cycle

you need to replace the water level switch

Posted on Sep 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool GSQ9669LW1 washer. Originally Load Size was set to small. After water was filled to that level and machine started to work, wanted to add more water. Turned the Load Size knob to Medium, nothing...


You would have to start the wash cycle all over in order to get enough water for the med load size. Once the washer starts it cycle you have to cancel that cycle to start a new one. Hope this is a help to your question

Apr 24, 2014 | Whirlpool Washing Machines

1 Answer

I have a Maytag Centennial top load washer. When washing in normal or heavy with large or super load size, the washer remains in sensing mode. Some water does start to fill, but never reaches wash cycle....


This unit does not handle a super large load as it advertised. When you put a super large load, the sensor is over-sized and will not move on the next cycle.

Sep 03, 2013 | Maytag Centennial MTW5800TW Top Load...

1 Answer

Over Flowing


OK, you have two issues here. you will need a new Water level pressure switch and, the timer will need to be replaced as well.

Jun 22, 2009 | GE WJSR2070B Top Load Washer

1 Answer

GE washing machine not draining and spinning


please change the washer between the hose that leads to water exit and the machine. this must have gone loose or worn out.

Jun 11, 2009 | GE WJSR2070B Top Load Washer

1 Answer

Continous water filling


HI, the water level switch is damaged on this unit. you will need to replace this switch. this will fix your level issue.

May 27, 2009 | Frigidaire Gallery GLWS1339EC Top Load...

1 Answer

Load size, spin cycle, and other cycles do not work properly


error code f 06 keeps coming up and we cannnot afford to have it serviced at this time we were told it had something to do with the control panel

Mar 22, 2009 | GE Profile WPSR3100W

2 Answers

Fill will not stop


you may have a problem with your pressure switch. or sometimes they call it the water level switch.

try to use it in the small level and see if it would stop filling around medium or large quantities of water.

if it would stop filling , then replace the water level sensor.

tnx 4 using fixya,

drcool

Oct 18, 2008 | GE WBB4500EWW Top Load Washer

Not finding what you are looking for?
Maytag PAV2300 Top Load Washer Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

606 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...