Question about Frigidaire GLTR1670A Front Load Washer

2 Answers

Front load Frigidaire Gallery washer

During the final spin cycle the washer does not spin the clothes at high revolution therefore they are sopping wet at the end of the spin cycle. The washer does toss the clothes at a light spin but never fast enough to get the water out of the clothes. Any suggestions

Posted by on

  • 6 more comments 
  • mavanya Dec 21, 2007

    I have the same problem, but ONLY on the permanent press cycle (with press saver option). I have had repairmen out four times but no one can fix it or tell me what is wrong. The last guy (yesterday) told me it was from too much soap. He suggested I run the same load again and again until there was no soap and it should spin dry then. I have run the same load through for two days now (no soap) and it still does not spin dry. Any thoughts????

  • Dr_Bob007 Dec 25, 2007

    Inconsistent High speed final spin cycle.

    To overcome the problem I need to reduce the load in the washing machine (sometimes by about 50%) for the High Speed Final Spin Cycle to 'kick in' and finish the job.

    Once spun, remove those spun clothes from the washing machine and place them into the dryer. Then replace the balance of the previously unspun 'wet' load and re-run the final High Speed Final Spin Cycle again.

  • Anonymous Mar 13, 2014

    My washer will spin, but the clothes are really wet at the end of the cycle and can't be put in the dryer

  • Anonymous Mar 17, 2014

    water draines but won't do last spin cycle leaving clothes dripping wet

  • Anonymous Mar 17, 2014

    the anti crease light is flashing and therefore wont wash and drain the load properly...clothes are sopping wet!

  • Anonymous Mar 20, 2014

    Maytag neptune front load washer Model mah6500aww. the time changes from 7 to 8 and back again. I can hear the water draining.

  • Anonymous Mar 27, 2014

    clothes still wet

  • Anonymous Mar 28, 2014

    washing cycles work extra rinse cycles work, but when it comes to the fast spin cycle it does not work it spins a very little slowly and then stops and moves back and forth slowly and then it stops and nothing happens then the wash cycle is over and my clothes are still wet with alot of water still left in the clothes



2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

You are having a door switch problem change it out and you will have a new washing machine.

Posted on Dec 15, 2007

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

How to changethe door around on a front loader washer

Posted on Dec 29, 2009


1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why does the washer stop during a load and "F 06"


The F6 error code means that the computer on the control didnt detect that the motor reached a high speed on the spin cycle, sometimes it thinks the washer didnt spin fast enough because of a loose wire connection either on the motor or the control boards (motor &machine control) if you find that the washer did actually spin at high speed (clothes dont come out sopping wet at the end of cycle) the wire connections or the motor control board will be the potential causes of the F6 error code


Sep 09, 2011 | Kenmore HE2 Plus Front Load Washer

1 Answer

Clothes sopping wet at end of all cycles

Here is a tip that I wrote a bout front load washer spinning and draining problems...

Front Load Washing Machine not draining and or not spinning


May 16, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Clothes coming out of washer still soaking wet

is it a kenmore top load?if so the motor is not kicking in to 2nd gear for high fast spin,does it have a speed control on the head?are you using it on the reg. wash cycle?-mike

Apr 18, 2009 | Washing Machines

1 Answer

Model 110 washer will not go into a final high speed spin.

hi, i would suggest the timer/programmer is faultyas it is ok on the other cycles, the noises you have described may have caused some damage,

Feb 10, 2009 | Washing Machines

1 Answer

How can i fix my washer myself?

The washer will not ever completely drain according to Maytag. A certain amount of water stays in the outter tub for balancing the machine for final hyper-spin. However if the machine is not spinning all of the water out and your clothes come out sopping the long thread I typed out to another person's about 2-3 questions up on the same topic

Dec 11, 2008 | Maytag Neptune MAH5500B Front Load Washer

2 Answers

Washer won't spin fast, only slow

tyr removing the lower acees panel from the uint , ther is a "button trap" located there to catch debris from entering pump assy, chances are its clogged and if it cant drain all the water it wont go into high speed spin, also you MUST use an HE detergent. HE detergent specifically designed for front loading washers

Apr 28, 2008 | Kenmore 44102 Front Load Washer

Not finding what you are looking for?
Frigidaire GLTR1670A Front Load Washer Logo

1,743 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers


Level 3 Expert

411 Answers

Jason Harris
Jason Harris

Level 2 Expert

274 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides