Digital umbro watch purchased 2001.How to change time please. 2 buttons on left. top light, bottom mode. 2 on right, top st/stp, bottom reset.

I am sorry but the time cannot be changed. But there is another option in which you can not see the date. Press mode button or the bottom left button until display shows T2 in the bottom left side. Press Reset button or the upper left button. Thus will make the hours number blink. Set the time using ST/STP button or the upper right button. To set the minutes, press Reset button or upper left button and the minutes number will blink and set it using the ST/STP button or the upper right button.

you had to press the mode and st/stp at the same time.

hi..

El stands for


To set the time

1. Press and hold [ Adj button ] till the digits on screen starts blink.
   
   
2. Now Press [ Mode Button ] repetitively to cycle through Hour -> minute -> Seconds
   
   
3. Press [ ST/STP button ] to adjust the value. Each press will increase the value.
   
   
4. Press [ Adj Button ] again to save the changes

To set the alarm

1. Press [ MODE Button] till it displays Alarm Time.
   
   
2. Repeat steps 1 to step 4 as described in 'To set the time'
   
   
   
3. Different watches have different procedures to active the alarm. Common method is pressing a button briefly.
   Since model of watch is not specified, Try pressing [Adj Button] or [ST/STP Button].
   

Time Setting Instructions:First press and hold ST/STP for a few seconds and make sure it says (Time 1). This watch has a (Time 2) to use in other time zones.You change from Time 1 and Time 2 by pushing the ST/STP button for a few seconds.Time 1 setting:- Press and hold the SET button (Light Function will blink) use the ST/STP button to select on or off. Then push the Mode button to go to the next function.- The Chime function will blink. Use the ST/STP button to select on or off and then push the Mode button to go to the next function.- Next will be to select 12hour or 24hour time by using the ST/STP button then press the Mode button to set the Hour, Minutes, and Seconds.- Continue to set the year but when you get to the Month/Day you have the option of putting the day first then the month, use the ST/STP to select then push the Mode button to enter the month and day.- When satisfied with your settings push the SET button and your done.
Time 2 Setting:- Press and hold the ST/STP button it will say Time 2 and then go away only showing the time and date for Time 2- To adjust this time to another time zone you push and hold the SET button.- Use the ST/STP button and the RESET button to move ahead or behind in hours depending on time zone. Push the SET button when done.-Your time 2 is set for a different time zone and your Time 1 is set for your local time. Remember to use the ST/STP button to go back and forth from Time 1 to Time 2.

The AquaSport watch? The one with the digital panel instead of hands? Push and hold the bottom right button (Reset) to get to the start of the menu. Use the bottom left to advance the modes and the ST/STP upper right button to change a display, such as time.

Truly unintuitive, but fun watch. If you're a masochist.

Go back to supplier!

I just picked up this watch.  Setting it is easy.  Hold down the button marked "RESET" (lower right) until the numbers start blinking.  Hit the "MODE" button (lower left) until the the settings you want to change are blinking.  Hit the "ST/STP" button (upper right) to change that setting.  Keep on hitting these two buttons until the settings are as you would like them.  Hit "RESET" button to finish.  So, to change just the day, I would hold down "RESET," hit "MODE" four times, hit "ST/STP" until the date is correct, hit "RESET" to save.  

i hope this helps....
the top right says st/stp....tells you the year
the bottom right is the light...
the top left is the reset....
and the bottom left is mode...alarm, stop watch,and time 2

Using a Sportline but I'm an hour off with daylight savings time. How do I change the time, I can't figure it out. Can

Press mode continuously for about 2-3 seconds then release
Press mode again so that the seconds are flashing
Press ADJ + ST/STP at the same time
Adjust what you need to adjust and move between minutes and seconds by repeating the ADJ + ST/STP
Good luck!
Malcolm S