How do i replace belt on a speedqueen top loader what do i take apart to put a new belt on

Hope these help
https://www.speedqueen.com/support.aspx

https://www.youtube.com/watch?v=miydioyULxU

https://www.youtube.com/watch?v=LMgRO4GAgBg

If the dryer is a front loader and if a top filter in filter it has two screw take them out and in front where top and front put a screw driver and pot the top up. When top came up on the side at top they are 5/16 screws take them out some of the front just slides up and off but if it has a full front door open door and on ea. side they are three screw take the top screw on top of the three screw out and slides door off and unhook wire on door switch on top of door. Look under drum and see how belt go on pulley so when you go to put it back on you will know how to. Take belt off pulley and drum and pick up on drum and pull it out and there is motor and gas heater and roller in back of wall now you have it apart.

Hello.

Loud noises coming from a Washing Machines are most often caused by loose objects inside the unit or by a broken dryer belt. The Washing Machines belt allows the dryer's motor to run smoothly. Continuous wear and dry conditions may cause the belt to dry out, eventually Washing Machines cracking and then snapping. This will cause a loud noise within the unit. Repair and fix the dryer belt of a Washing Machines to get rid of loud noises.

Instructions And Things You'll Needed to solve the problem.

Screwdriver ,Replacement Washing Machines belt

1 Stop the Washing Machines and look inside the dryer's drum for any loose objects such as coins, pens or anything else that may have been in a pocket of clothing. Remove the object and restart the dyer to determine if the noise has stopped.
2 Unplug the Washing Machines from the wall outlet to disconnect all power to the unit.

3 Remove the lint trap from the lint compartment on the top of the dryer.

4 Remove the screws that hold the top panel in place. Pull the panel off to access the
dryer belt.
5 Tilt the dryer forward and lift the dryer drum to remove the belt. Check the Washing Machines belt. A belt that is worn, cracked, split or broken will cause loud noises.

6 Slide the old belt off of the drum and pull it out to remove it. Take note on how it is positioned over the drum.
7 Install the new belt. Lean the front panel away from the Washing Machines and slip the new belt over the drum. Locate the position of the old belt and slip the new belt following the old belt's position ensuring the grooved side of the belt faces down. Push the idler pulley towards the motor to allow you to slip and loop the belt around the motor pulley.
8 Place the top panel on the Washing Machines and screw it in place.
9 Open the Washing Machines door and use your hand to rotate the drum counterclockwise a few turns to ensure the belt is secured.
10 Plug the Washing Machines into the wall unit and begin use .

check the pump filter first,, if its blocked up clear it out
then check that the pump is working it may just be stuck up,,,

Usually when this unit washes but will not spin the thrust bearing kit is damaged.This is easy to repair with little cost.
Completly empty the unit, clothes and water ,unplug the power cord, lie the unit on its back, remove the belt,the c clip from the pully. Take the thrust bearing,the pully the washers off the unit . Grease the new bearing and install new parts. I would also replaced the belt.

It's not that hard, but it can be a little tricky. First UNPLUG the dryer or turn off the gas to it, whichever is applicable.

Then, assuming you have the new belt, you will open the lint filter door. There will be two screw heads visible. Remove them. Place a knee in the center of the dryer just below the top. Place your hands at the front corners and **** hard while pressing with your knee and lift up on the top of the dryer. Once you do this, tilt the dryer top back until it rests on the wall behind the dryer.
Next remove the two bolts at the top front corners. Disconnect the wiring harness connector for the door switch and lift the front panel of the door up and away from the rest of the dryer. You will notice the drum rides on the front panel and will fall down.
Take out the old belt. Loop the new belt around the drum in the same approximate position that the old belt was riding. Take a small loop of belt and push it through the tensioner while lifting the tensioner to relieve tension off the belt. Then loop that end around the motor pulley.
To re-assemble the dryer, reverse the directions for taking it apart. Remember to hook up the wiring harness. You will have to lift the drum into place to make sure the felt on the front and rear ride correctly on the guides.

Good luck!

is the pulley wably?

more information needed to specifcally match the model
however dryers are all similar so
generically, UNPLUG dryer

A:top mounted lint filter (kenmore maytag(New))

• remove lint filter
• remove screws in lint filter housing
• with putty knife or other flat blade depress lock tabs at front corners of top body panel
• tilt top panel up
• remove screws 1/3 way down each side, remove door switch wires
• remove front panel set aside

B:dryers with screws at bottom of front panel (maytag speedqueen)

• remove screws from bottom of front panel
• tilt front panel up
• remove door switch wires
• remove front panel set aside

All

• pull drum forward & out
• examine drum felts, rollers, and slides for wear replace if worn
• wrap new belt round drum at old wear marks
• insert drum
• wrap belt round motor pully
• pull tensioner pulley hard to end of travel against spring
• wrap belt round tensioner pulley
• release tensioner

reassemble

The brakes are probably stuck or the cam that releases them is damaged