Question about Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore washers, heavy duty 80 series, no spin

Kenmore washers, heavy duty 80 series, extra capacity,no spin cycle


Posted by on

  • moezeo Oct 14, 2009

    I think that sounds just right. once when i got it to spin i could open the lid and thought that was screwed up. it never started again.

    thnx

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 744 Answers

Hello, Your problem is going to be with your lid switch, this is located normally either in the control panel or about half way down on the right side under the lid. This is a safety feature to stop you opening the lid while the machine is in a high spin. Once you have located the switch trace the wires back to the wire harness in the control panel. Disconnect the lid switch from the wire harness and with an ohms meter check for condinuity on pin 1 & 3 (the 2 outside pins not the middle this is a ground) You should find you have no condinuity and should replace this switch. If you have any other questions or concerns please feel free to comment again. Good Luck!! Mike

Posted on Oct 14, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have kenmore 80 series heavy duty/ super capacity plus washer that after it fills with water,hot or cold and it starts the wash cycle, I noticed that the agitator only moves once in awhile and stops


hum either a bad timer sticking the point contacts close. have u tried this in all cycles? and possibly a motor with bad windings not enough power to run agitation? try running in mild or gentle and see what happens? I was tempted to say the cam dogs in agitator but they dont work then stop then work, when they go out they go out.

Feb 17, 2015 | Kenmore Washing Machines

1 Answer

Kenmore Heavy Duty 80 Series Extra Capacity Plus Model# 92480200. The washer will begin to fill and will not stop filling regardless if water level setting is on low, medium or high and will overflow and...


The problem is the pressure switch has failed or the hose is plugged up, has a hole in it. These are usually inexpensive and are very easy to replace. Here is a video this will walk you thru testing and replacing a pressure switch. You can also enter your model # for diagrams and illustrations of your specific model. All parts come with installation instructions. Not all models are available.

Oct 30, 2010 | Kenmore Washing Machines

3 Answers

How many cubic feet are in the Kenmore Washer Model 110 80 series


The cubic feet of the Kenmore washer model 110 heavy duty is 2.8 cubic feet. Measured to the top water line 14.5 inches and using the radius of the tub of 10.375 inches.

Oct 26, 2009 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

Rinse cycle do not disengaged


does it drain?did you check the lid switch?

May 17, 2009 | Kenmore Washing Machines

1 Answer

Washer won't drain


Dear cbringer,
I have the same washer. I have had the same problem with it. It's the timer module. You can get additional help from http://www.repairclinic.com.

Hope This Helps,
Jay

Mar 12, 2009 | Kenmore Washing Machines

1 Answer

Won't spin or drain


Check to make sure your lid switch is working.

Nov 17, 2008 | Kenmore 22422 Top Load Washer

1 Answer

I also need the answer...


where is the lint trap located

Dec 06, 2007 | Washing Machines

1 Answer

I also need the answer...


Verify Lid switch ..... A solved rating is great motivation to continue giving priceless advise........

Oct 03, 2007 | Kenmore 22422 Top Load Washer

Not finding what you are looking for?
Kenmore 24032\24036 Top Load Washer Logo

533 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5692 Answers

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...