Power cord connection issue---we have tried different power cords. Issue is where it connect to set. The power will come on, but the set will shut off

I'm sorry to hear that you're experiencing an issue with the power button cord on your Epson SC P600 DTG mod.
To address this issue, you'll need to locate the cord and make sure it is properly connected. Follow these steps to troubleshoot the problem:

1. Turn off the printer and unplug it from the power source.
2. Check the cord connection on both ends. Make sure it is firmly attached to the power button and the printer head or board.
3. If the cord is loose, carefully reattach it to both ends.
4. Plug in the printer and turn it on to test if the issue has been resolved.

If the problem persists after following these steps, it may be necessary to seek assistance from a professional technician or the manufacturer.

If you have replaced the circuit board and there is still no power to the front panel, there could be a few things causing the issue. Here are some things you can try:

1. Check the power cord: Make sure the power cord is securely connected to both the TV and the wall outlet. You can also try plugging the TV into a different outlet to see if that solves the issue.
2. Check the power supply: If the power cord is connected properly and the TV still isn't receiving power, there may be an issue with the power supply. Check the power supply for any visible damage or loose connections.
3. Check the internal fuse: Some TVs have an internal fuse that can blow out, causing a loss of power. Check the owner's manual to see if your TV has an internal fuse, and how to check and replace it if necessary.
4. Contact a professional: If none of the above solutions work, there may be a more serious issue with the TV that requires professional repair. Contact a qualified technician or the manufacturer for assistance.

If your Nebo Recline 1500 won't charge despite trying different cords, there are a few troubleshooting steps you can try:

1. Check the charging port: Make sure that the charging port on your Nebo Recline 1500 is clean and free of debris. If there's any dirt or debris inside the port, it may be blocking the charging cord from making a proper connection.
2. Try a different power source: If you've tried different cords but still can't get your Nebo Recline 1500 to charge, try plugging it into a different power source. It's possible that the power source you're using isn't providing enough power to charge the device.
3. Reset the device: Try resetting your Nebo Recline 1500 by pressing and holding the power button for at least 10 seconds. This should force the device to power off and then power back on, which may help resolve any charging issues.
4. Contact customer support: If none of these steps work, it's possible that there's a hardware issue with your Nebo Recline 1500. In this case, it's best to contact the manufacturer's customer support team for further assistance. They may be able to help you diagnose the issue or provide repair/replacement options.

whats the exact issue?

1. Turn on the Canon MP 530 printer by following the steps below
2. Interrupt the connection between the printer and wall outlet by removing the power cord.
3. Leave the printer aside for next 10 minutes.
4. Bring the power cord connection back to the printer and make sure that you connect it to the wall outlet directly and not by using any socket box.
5. The printer turns on automatically after the connection.
6. If the printer is not turning on, then try to repeat the same steps by connecting it to a different outlet.
7. If you have an optional power cord, use it along with the printer.
8. Following the above steps should have fixed the issue and if the issue persists, then service the printer. Call our Toll-Free (1-866-293-9220) to get quick support

When a PlayStation 3 Fat model experiences issues where it turns on briefly with a green light, then transitions to a blue light within seconds before shutting off, it could indicate a hardware or power supply problem. Here are some troubleshooting steps you can try to address this issue:
1. **Power Cycle the PS3**:
- Unplug the power cord from the back of the PS3 and wait for a few minutes.
- Plug the power cord back in and try turning on the PS3 again to see if the issue persists.
2. **Check Power Connection**:
- Ensure that the power cord is securely connected to the power outlet and the PS3 console.
- Try using a different power outlet or power cord to rule out power supply issues.
3. **Remove and Reinsert Hard Drive**:
- Turn off the PS3 and remove the hard drive from the console.
- Reinsert the hard drive carefully and ensure it is properly seated.
- Turn on the PS3 to see if the issue is resolved.
4. **Check for Overheating**:
- Overheating can cause the PS3 to shut down automatically. Make sure the console has proper ventilation and is not overheating.
- Clean any dust or debris from the vents and fan to improve airflow.
5. **Reset Video Settings**:
- Turn off the PS3 by pressing and holding the power button until you hear two beeps (about 10 seconds).
- This will reset the video settings. Turn on the PS3 and see if the issue is resolved.
6. **Inspect for Hardware Issues**:
- If the problem persists, there may be internal hardware issues causing the shutdown.
- Consider seeking assistance from a professional technician or Sony support for further diagnosis and repair.
7. **Contact Sony Support**:
- If none of the above steps resolve the issue, it is recommended to contact Sony PlayStation support for assistance.
- They may provide additional troubleshooting steps or advise on repair options.
If the PlayStation 3 Fat model continues to exhibit the same issue despite troubleshooting, it may require professional inspection and repair to address the underlying hardware problem causing the shutdown.

Try switching to a different HDMI port if one is available. If this is not the issue you may have an issue with your HDMI cord the only way to troubleshoot this would be to try a different cord. If you have tried a new cord and it still does not work you have an internal issue with your Television or the item that you are trying to connect to it.

Hi,

This is not Printer or PC USB port issue.

You need to drain the power from PC.

Follow these steps to resolve the issue

1. Disconnect the printer power cord from walljack or surge protector
2. Disconnect the USB cable of printer from PC or vice versa
3. Power off your PC, Disconnect the power cord from wall jack
4. Wait for 5-10 mins
5. Connect the PC power cord and power on the PC and wait till you are able to login to your PC
6. Connect the Printer power cord
7. Connect the USB cable to PC or vice versa you disconnected.

This should resolve the issue.

Try connecting a different device to the TV and check. You may also try changing the cable to connect the device to the TV and check. If the issue persists, try resetting the TV to the factory settings, then try power reset. To power reset the TV, please disconnect the power cord for a short period of time (approximately 1 minute). Then, reconnect the power cord and power on the TV. If the issue still persists, then service may be required.

Hi,

Try to connect your printer to a different power outlet and check if that causes the problem or try connecting a different power cord. In case the issue still thesame after using a different power cord, there could be a problem with the power button of the printer.

Keep me posted.