Washer does not sense that the door is locked flashes do will start filling then flashes fl although door is locked

Bad connection to power of the fill switch or not airtight to the hose on it.

E:FL - Fill Error - Pressure switch fails to open in 30 minutes in any fill agitate cycle.

Speed Queen Fault Codes - PartSelect

https://www.partselect.com > JustForFun > Speed-Queen-F...

FL means the door failed to lock
DO means washer door is sensed as being open.

The good ol' Whirlpool Lid Lock Flashing Light Problem - ApplianceBlog

www.applianceblog.com/.../42456-The-good-ol-Whirlpool-Lid-Lock-Fl...

Dec 11, 2013 - 10 posts - ‎3 authors
Red Lid Lock light flashing intermittently when you try to start a cycle. ... I'm going to post what SENSING does first, then you will need to locate your tech. ... start with thelid lock on and blinking, or the unit will not start and spin. FIXED Sense light on light humming noise won't start ...
8 posts
Aug 9, 2015
Whirlpool WTW4950XW not working
10 posts
Nov 2, 2013
Stacked GE washer/dryer lights Blinking doeent start at ...
5 posts
Feb 20, 2012
More results from www.applianceblog.com

Washer Sensing led (Green) on with the lid locking led (Red ...

www.shopyourway.com > Manage My Life > Questions

... this: Sensing led (Green) on, the lid locking led (Red) blinking with a clicking noise ... red led light goes off green led light stays on and the washer does not start.

• dc--Unbalanced load preventing washer from spinning
• dL--Door is in locked when washer is running
• dS(d5)--Door is open when washer is open
• FL--Washer failed to lock the door
• Hr--Water temperature control problem(Heat control problem)
• LE--Washer tried to fill but has not reached proper water level(Slow fill)
• LO--Door will not unlock
• E3--Motor not running properly
• nd--Washer is not draining/Washer senses a brief restriction while draining
• nF--Washer tried to fill but was unsuccessful
• Sr(5r)--Problem with control
• PF--Power failure, electric service was lost while washer running
• OE--Fault detected in water level sensor
• E2--Jammed key
• bE--Motor speed sensor problem
• tE--Temperature sensor problem
• 3E--High current detected
• 2E--High/low voltage detected
• 8E--Vibration sensor problem
• 7E--Silver Care control problem
• SUdS--Too much suds detected during wash cycle, unit on hold until suds reduced

The "FL" is indicating that the door has failed to lock or it locked but the control does not sense the door has locked.

It could be caused by:

• faulty door lock solenoid
• loose wire connection
• faulty door lock switch
• faulty door lock sense switch
• bad control board
• 
  

Here is a link to the manual for your machine also.

The "FL" is indicating that the door has failed to lock or it locked but the control does not sense the door has locked.

It could be caused by:

• faulty door lock solenoid
• loose wire connection
• faulty door lock switch
• faulty door lock sense switch
• bad control board

fl is usally a water not detected problem,, check ur fill hoses for kinks make sure ur water is on,, possibly have a bad fill valve..

FL:
Failed to lock.

Trigger:
Door lock monitor switch in door lock mechanism unable to communicate to control board the door is locked.

Action to be taken:
1.Check wire connections in harness leading from machine control board to door lock mechanism.
2.Check solenoid and door lock enable switch in door lock mechanism.
3.Replace responsible component.

If you need to open the door.
Maytag's Neptune washer has a latch and lock on the door. If this lock fails to open when the cycle is finished. You can rescue your clothes by:
1) Remove the bezel from the soap/bleach/fabric softener dispenser.
2) Locate the red cord near the right front corner of the dispenser opening. Pull on this red cord. This will unlatch the door so you can rescue your laundry. Then call for service.


Best of luck, Any questions just ask

The "FL" is indicating that the door has failed to lock or it locked but the control does not sense the door has locked.

It could be caused by:
faulty door lock solenoid
loose wire connection
faulty door lock switch
faulty door lock sense switch
bad control board

I recommend calling a service technician to diagnose and repair your washer.
but try this first just in case....unplug it for 1 minute plug back in and see if the fault code clears.
good luck.

thanks